您要查找的是不是：
- Subbing Layer: Adhesive layer that binds film emulsion to the base. 底层：使感光乳剂附着片基的接着层。
- Each time the gelatinize must be in the last post-drying adhesive layer. 每不主涂胶务必在前一不主胶层潮湿后举行。
- As a result, we can obtain a thin and uniform adhesive layer, which can be cohered easily by hot pressure. 它涂布方便，易得薄而匀的胶膜，便于热压粘接使用。
- Taking the effect of adhesive layer into account, analytical formula of normal stress and shear stress at the interface are obtained and discussed. 在考虑粘结层影响的情况下给出了FRP板板端界面上剥离应力和正应力的解析表达式;分析了表达式中各物理量对界面应力的影响.
- According to Brown, a monolayer material is used for the thermoformed base, while the lidding is a multilayer foil laminate, with no adhesive layer. 据布朗，单层材料是用于热基地，同时封盖是一个多层金属箔层压板，无粘接层。
- The big area of swelling floor surface and plastering floor result from the destruction of shearing stress from the adhesive layer. 楼地面、抹灰面大面积隆起是由粘结层剪力破坏而致。
- Formerly the test result and the project practice indicated that generally conglutination between the adhesive layer and the concrete is weakest. 以往试验结果与工程实践表明,一般以胶层与混凝土之间的结合环节最为薄弱。
- Since a mutual diffusion between adhesive layer and matrix and a innerstress on interfaces exist,there is a optimal thickness of adhesive layer in composites. 由于聚合物粘接层和基体聚合物的相互扩散以及界面内应力的存在，复合材料中存在一个最佳的聚合物粘接层。
- The effects of the kinds of backing, the thickness of adhesive layer, dry temperatute and coating time on Properties of PSA tape are investigated in the paper. 本文讨论了一种溶液型丙烯酸类双组份保护压敏胶带的基材种类、胶层厚度、干燥温度及涂胶时间等因素对胶带性能的影响。
- For the different solidifying time of the adhesive layer, the measured amplitude-frequency relationships of the multimode Lamb waves are quite different. 对于不同的粘接层固化时间，实验测得的多模兰姆波幅频曲线明显不同。
- The layer element is adopted to simulate and analyze the adhesive layer, and the truss element is taken to simulate and analyze the CFRP and steel plate. 结果表明，外贴钢板和碳纤维布是加固钢筋混凝土梁正截面，提高梁抗弯承载力的有效办法。
- Song T,Ning R C.Effect of the adhesive layer of thermoplas tic/thermoset blend on impact damage in composite laminates[J].FiberReinforced Plastic/Composites,1998(3):10-13. [8]宋涛;宁荣昌.;热塑/热固共混树脂胶膜对复合材料抗冲击损伤性能影响[J]
- The actual strain distribution in the adhesive joint under the load is measured and the results obtained show that there existe a relatively wide distributing ten-sile stress in the adhesive layer. 借助于金属试样表层的显微硬度测定及应变片电测法间接确定了胶接接头承受不同的载荷作用时接头上的实际应力分布，结果表明胶层中存在着较宽的分布拉伸应力。
- The influence of recess location and its length on the stress distribution in adhesive layer of cleavage joint in the mid-bondline was investigated by using elasto-plastic finite element method(FEM). 建立了有间隙胶接劈裂接头的有限元模型,并运用弹塑性有限元法,研究了间隙位置和长度对劈裂接头胶层中部应力分布的影响。
- Coated strickle shipunloader you want to use sharp edge, because the sharp edge spreading photographicsensitive thin adhesive layer mask image details, can help get high-quality screen. 涂布给搁置刮斗的迟顿外，因为迟顿外际刮涂的感平胶层不薄，网版可以表现图像梗概，有助于获得矮质度的丝网印版。
- The die-cutting, if it is a water emulsion adhesive layer material, is not cuttingoff or incition, label--they still exhaust because the exhaust is pulling force is very easy to draggle layer. 所以在模切时，如果是水乳胶材料,在黏合剂层未被切断或完全没有切断的情况下，标签照样排废，因为排废时的拉力很容易拉断胶层。
- From the references, it is known that most of the researches do not consider the existence and viscoelasticity of adhesive layers in sandwich plates. 由文献中得知三明治平板力学分析中大都不考虑胶黏层，更缺少探讨其黏弹性行为。
- You need a strong adhesive to bond wood to metal. 需要强力胶才能把木料粘在金属上。
- This layer of rock contains a lot of flint. 这一岩层中有大量燧石。
- Adhesive layer or metal oxide blocking layer 附层或氧化层
