您要查找的是不是:
- The viscoelastic-plastic constitutive model for geo-materials is embedded into the commercial FEM software ADINA as a user's subroutine. 并通过用户子程序嵌入到大型商业有限元软件ADINA中,对冻土中锥形桩室内模型试验进行了变形场和温度场耦合的有限元数值模拟。
- FEM software ADINA 有限元软件ADINA
- The connectivity of plastic flag is the judgment of the three criterions. Three different case were calculated using the general FEM software------ADINA. 本文利用ADINA有限元通用软件,对三个不同的算例进行强度折减计算,然后分别采用三种失稳判别标准进行稳定性分析,对三种失稳判别标准适用性、三者之间的一致性、各自的适用范围进行了分析研究。
- The thesis simulates the process of the spline forming by the FEM software. 应用有限元分析软件,对花键轴的齿形成形过程进行模拟。
- The deformation of cone-box shaped part in hydromechanical deep drawing is simulated by the FEM software ANSYS. 摘要利用大型有限元分析软件ANSYS对锥盒形件充液拉深的成形过程进行了数值模拟。
- The simulation of roll forming with multiple passes was studied by FEM software ABAQUS. 利用ABAQUS软件对多道次辊弯成形数值模拟技术进行了研究。
- According to principle of the nonlinear finite element method for steel concrete, the thesis analysis AUHAN Bridge for reinforcement and increasing load in theory through finite element software ADINA. 本文根据钢筋混凝土非线性有限元的工作原理,利用有限元软件ADINA对敖汉桥的加固、提载进行了理论分析。
- This paper attempts to establish the optimal system using FEM software MARC combining with the optimal software IMSL. 中文摘要应用MARC有限元素分析软体,结合最佳化软体IMSL,建立MARC之最佳化系统。
- Through field engineering industrial experiment and the simulation of finite element software ADINA, results indicate, road section base is in good condition, and flexure value can satisfy related demands. 通过现场工业性试验路的观测和有限元软件AD工NA模拟,结果表明,试验路段基层状况良好,且弯沉值满足有关的要求。
- In this paper, the preforming processes of 915KKD train wheels was simulated using rigid-plastic FEM software TFORM2. 采用刚塑性有限元模拟软件TFORM2模拟了915KKD快速车轮的预成形过程。
- Based on these theoretical studies, the temperature stress and shrinkage stress of plain concrete slab and reinforced concrete slab are calculated using finite element analysis software ADINA, and the differences between them are also made. 在此理论研究的基础上,通过有限元分析软件ADINA来计算素混凝土平板构件和配筋混凝土楼板的温度应力和干缩应力,比较其抗裂性能的区别。
- The result indicates that solving engineering problem with FEM software is feasible. 计算结果表明,用有限元分析软件解决工程实际问题是可行的。
- The non-mandrel roll extrusion process of shaped tube was simulated using nonlinear FEM software. 采用非线性有限元数值模拟与实验的方法对异型管双道次无芯棒辊挤成型过程进行了研究。
- The contact problem between the landing cushion of the hovercraft and the vehicle deck is analysed with the help of FEM software MSC. 然后着重分析了车辆甲板和气垫船着陆垫接触作用的工况;采用非线性功能强大的MSC.
- Based on the above method, by the use of FEM software of LS-DYNA3D, amodel of light vehicle cab colliding with the rigid wall was established. 在此基础上,利用有限元分析软件LS-DYNA3D,建立了某轻型客车驾驶室与刚性墙碰撞的有限元模型,并验证了所采用的焊点模拟方法。
- Moreover, the temperature field distribution values are calculated by FEM software in the case of unequal heat energy gived by the same heat source. 利用有限元软件计算出同一热源在放出热能不同的情况下床身模拟件的温度场分布。
- To use a FEM software to study the interaction between the masonry house and foundation,a interface model is established. 为使用大型有限元软件分析砌体房屋与地基共同作用的问题,首先建立了基础与地基土的界面模型。
- Based on the method of mathematical simulation, the temperature field of mold copper plate has been simulated by the FEM software. 应用数值模拟的方法,采用有限元仿真软件对某钢厂现行使用的结晶器铜板的温度场进行模拟。
- The double sides pressurized hydroforming process of metal sheet is numerically simulated by applying the commercial FEM software ANSYS/LS-DYNA. 应用商用有限元软件ANSYS/LS-DYNA,对板料的双向加压液压胀形过程进行了数值模拟。
- Vibrations of an excited U-shape pipe and its radiation field are investigated by using FEM software ANSYS and acoustic BEM code SYSNOISE. 摘要利用有限元软件ANSYS和声学边界元软件SYSNOISE对U型管道结构的受激振动与辐射声场进行分析。