您要查找的是不是：
- Gas Jet Nose Tip 喷气式飞机前端
- Put a match to the gas jet to light the gas. 把火柴放在煤气炉嘴上来点燃煤气。
- Muzzle length is 40% of the total head length from occiput to nose tip. 口吻的长度占整个头部长度（从后枕骨到鼻镜的距离）的40%25。
- "I also continue at the nose tip, went winter, spittle-spraying my face. 又继续指着我的鼻尖，喷着酒气，唾沫星喷到我的脸上。
- The bridge of the muzzle is straight.Muzzle tapers slightly from stop to nose tip. 鼻梁很直，从止部到鼻尖成轻微的锥形。
- Right: Small amount of self cartilage taken from the patient's rt. ear grafted into the nose tip, 4 days after surgery. 在本诊所以往做过这种手术的案例中;几乎全部都是在三天至一周内恢复上班;而未被同事看出异状.
- You left the gas jet on again. One of these days we'll all be blown to kingdom come. 煤气的喷口你又没关。总有天我们都要被炸上天的。
- A device on a stovetop,such as a gas jet or electric element,that produces heat. 燃烧器位于火炉顶部的产生热量的设备，如汽油喷嘴或电动装置等
- Methods:7 cases of the defects on nose tip or nasion after the operations were repaired with forehead skin flap,11 cases of the defects on nasal alae with naso labial skin flap. 方法:位于鼻尖或鼻根部术后缺损用前额皮瓣修复7例,鼻翼部缺损用鼻唇沟皮瓣修复11例。
- A device on a stovetop, such as a gas jet or electric element, that produces heat. 燃烧器位于火炉顶部的产生热量的设备，如汽油喷嘴或电动装置等
- Liquid-liquid &gas jet pump is a kind of li quid jet pump which can pump two-phase liquid and gas fluid. 液-液气射流泵是一种能同时抽吸液、气两相介质的液体喷射泵。
- The launch was delayed by one week after JAXA said it had discovered a problem with the gas jet thruster for its launch rocket. 这颗卫星将让学生在亚洲国家的沟通顺畅，并没有相隔的时间，好像他们在同一个教室。
- Results show that gas jet with high speed can increase the surface temperature of tube,decrease its temperature difference. 结果表明,高速煤气射流有利于提高辐射管表面温度,降低温差,改善温度分布均匀性。
- In this paper, the time-dependent ignition process of gas jet for launch underwater was studied by means of numerical simulation. 本文采用数值模拟方法，对导弹在水下点火发射燃气射流初期这一非定常过程进行了研究。
- The use of cryogenic nitrogen gas jet to reduce the temperature of cutting zone and to avoid oxidation wear of tool in high speed milling titanium alloy was presented. 为降低切削区温度、防止刀具的氧化磨损，提出在低温氮气射流条件下进行钛合金的高速铣削加工。
- Computer modeling, as a means of studying the mixture formation in diesel engines, is used in the study of the development and wall impingement of an unsteady gas jet. 用计算机模拟方法研究了非稳态+气体射流的发展及碰壁过程,作为了解柴油机喷雾混气形成过程的辅助手段。
- The structure intensions of parts impacted by the gas jet during the launching process are analyzed by using EEM, and the relative results are contrasted with the axial state. 用有限元方法分析了发射过程中受燃气射流冲击的零部件的结构强度，并与放列状态进行了对比。
- The experimental results indicate that cryogenic nitrogen gas jet with minimal quantities of lubricant is the most effective cooling and lubricating mode to reduce milling force and to retard tool wear. 试验结果表明，低温氮气射流结合微量润滑能够最有效地降低铣削力，抑制刀具磨损。
- Based on the thermal environment, three thermal protection schemes were put forward, i.e. regeneration cooling scheme, C/SiC thermal protection scheme and gas jet thermal protection scheme. 提出了支板前缘金属结构再生冷却方案、耐烧蚀材料热防护方案和气体喷射热防护方案，并对这三种方案的热防护效果进行了数值模拟。
- Analysis of mass transfer of liquid gas jet pump 液气射流泵传质分析
