您要查找的是不是：
- Gauss heat source model 高斯热源模型
- The general loading arithmetic of Gauss heat source in ANSYS welding simulation is loading heat flux(HF)on the whole welding surface based on TABLE array parameters. ANSYS焊接仿真中高斯热源的一般加载算法是:基于表参数的整面热流密度加载。
- Heat source model is the shoe pinches of the temperature field numerical simulation for laser beam penetration welding. 热源模型是激光深熔焊温度场数值模拟分析的关键。
- The 2D computed temperature by using heat source model of double ellipsoidal Gaussian distribution gives best agreement with the measured value. 利用双椭圆热源分布的数值计算模型和实际检测二维温度场分布结果作为边界条件，获得了整个焊件更宽温度范围和三维温度场分布的在线模拟。
- The border of laser beam penetration welding seam is simulated by the constructed heat source model and compared with the experimental results. 应用所建立的热源模型模拟分析了激光深熔焊焊缝边界形状,并与实验结果进行了比较。
- Directly employing moving double ellipsoid heat source model in electron beam welding numerical simulation will lead to huge calculation and low efficiency. 直接利用移动双椭球热源模型对电子束焊接过程进行数值模拟时,计算量庞大,计算效率低下。
- Rotary-Gauss body heat source model can show appropriately the character of electron beam deep penetration welding, but only smooth “parabola” shape weld can be obtained. 旋转高斯曲面体热源模型,能较好的反映电子束焊接深熔焊的特点,但只能得到圆滑的“抛物”形焊缝。
- A method to determine ground thermal properties used by in-situ field thermal response tests was established based on the cylindrical heat source model. 在埋地换热器圆柱热源模型的基础上采用参数估计法建立了一套可用于现场确定土壤热物性的方法。
- HEAT SOURCE MODEL FOR TWIN WIRE WELDING 双丝焊热源模型
- Using two kinds of different heat source models including Gaussian distribution and double-ellipsoid distribution,the differences of the computation results were compared. 分别采用高斯分布函数、双椭球分布函数两种不同的热源分布模型进行加载,比较两种热源模型下计算出的温度分布情况差异。
- Advance in research of welding heat source model 焊接热源模型的研究进展
- Based on Gaussian heat source model and double ellipsoid heat source model respectively, the calculating formulas of two models in double wire welding were derived, the proper finite element model was constructsed. 摘要分别以高斯热源模型及双椭球形热源模型为基础，推导出两种模型用于双丝焊的计算公式，建立了合适的有限元模型。
- virtual region heat source model 虚区域热源模型
- Gauss heat source 高斯热源
- Pilot study of a heat source model for weaving welding arc 模拟焊接过程电弧摆动的热源模型
- The combined model with Gauss surface heat source and cylindrical heat source was used according to both the nail-shaped weld and the deep penetration of electron beam welding. 针对电子束焊接特有的钉头状焊缝及其穿透深度大的特点,采用高斯面热源与柱体热源组成的组合热源模型,对焊接温度场进行分析,模拟结果与实际焊缝取得了良好的一致。
- A new heat source model in numerical simulation of high energy beam welding 高能束焊接数值模拟中的新型热源模型
- Do not place LCD on heat source positions. 不要把显示器放在热源位置上。
- Analysis of heat source model used in temperature field simulation for laser beam deep penetration welding 激光深熔温度场数值模拟热源模型分析
- ESTABLISHMENT OF SEGMENTED MOVING DOUBLE ELLIPSOID HEAT SOURCE MODEL IN ELECTRON BEAM WELDING NUMERICAL SIMULATION 电子束焊接数值模拟中分段移动双椭球热源模型的建立
