您要查找的是不是:
- First, we substitute linear Hall sensor signal for general FOC which can directly produce various phase current commands in three phase stationary frames. 霍尔元件讯号由查表的机制可计算得到马达转子位置,进而能得到转速讯号,以达到速度控制的目的。
- Hall sensors are mounted in such a way that the zero crossing of the BEMF occurs as close as possible to the zero crossing of the Hall sensor signal associated with the corresponding coil. 对于霍尔传感器而言,其安装位置的出发点要尽量使得各绕组对应的霍尔元件产生的信号的过零点与反电动势的过零点位置接近。
- Hall sensor which contains signal amplification and waveform shaping. 其中霍尔传感器包含信号放大和波形整形。
- Hall sensor signal 霍尔位置信号
- REPAIR HE OPEN AMBIENT TEMPERATURE SENSOR SIGNAL CIRCUIT. 修理开路的周围温度感知器信号电路。
- WHILE ROTATING THE TIRE, OBSERVE THE RR WHEEL SPEED SENSOR SIGNAL. 旋转轮胎是,观察右后轮速感知器信号。
- The circuit of toilet servomechanism which used hall sensor was designed. 设计了基于霍尔传感器的卫生间自动控制器电路。
- USING AN OHMMETER, MEASURE THE BATTERY TEMP SENSOR SIGNAL CKT. 使用欧姆计,测量电池温度感知器信号电路。
- REPAIR THE OPEN CRANK POSITION SENSOR SIGNAL CIRCUIT. 维修断开的曲柄位置感知器信号电路。
- BATTERY TEMP SENSOR SIGNAL AND SENSOR GROUND CKTS FOR RESISTANCE. 电池温度感知器信号和感知器接地电路S的电阻。
- WHILE ROTATING THE TIRE, OBSERVE THE LF WHEEL SPEED SENSOR SIGNAL. 当转动轮时,观察左前轮速度感知器信号。
- WHILE ROTATING THE TIRE, OBSERVE THE LR WHEEL SPEED SENSOR SIGNAL. 在转动车轮胎的同时观察左后轮速度感知器信号。
- In this paper, the detecting current problems of applying highperformance LEM hall sensor are studied. 为此,分析研究了应用高性能的LEM霍耳传感器检测电流的问题。
- Abstract :This paper describes the design speed and Odometer to SCM system and the smallest Hall sensor at the core. 摘要:本文介绍的速度与自行车里程表设计以单片机最小系统和霍尔传感器为核心。
- The products including: Power Management IC、 Hall Sensor IC、 PLD、 Memory Chip、 MCU etc. 专注于模拟器件,数字集成电路之推广销售。
- CONNECT A JUMPER BETWEEN THE BATTERY TEMP SENSOR SIGNAL AND SENSOR GND CKTS. 电池温度感知器信号和感知器接地电路S之间设一条跳线。
- An on-chip commutation decoder and state machine reads the inputs of three Hall sensor inputs (or IO outputs from a microprocessor). 芯片整流解码器兼状态机读取三个霍尔传感器输入的输入(或微处理器的IO输出)。
- The device consists of a precise, low-offset, linear Hall sensor circuit with a copper conduction path located near the surface of the die. 该器件具有精确的低偏置线性霍尔传感器电路,且其铜制的电流路径靠近晶片的表面。
- The device consists of a precision, low-offset linear Hall sensor circuit with a copper conduction path located near the die. 该器件由一个低偏移的精密线性霍尔传感器电路组成,其铜制的电流路径靠近晶片的表面。
- The devices consist of a precise, low-offset, linear Hall sensor circuit with a copper conduction path located near the surface of the die. 该两种器件具有精确的低偏置线性霍尔传感器电路,且其铜制的电流路径靠近晶片的表面。