您要查找的是不是：
- Hot runner heating power 热流道加热功率
- Keywords hot runner plate;thermal expansion;counterbalance;heating power;injection mould; 热流道板;热膨胀;补偿;加热功率;注射模;
- The cost of valve gated hot runner is US$2,500 per cavity. 针阀热流道每腔的成本超过两万元。
- HOT RUNNER SYSTEM,TEMPERATURER CONTROLLER. MOLDCOMPONENT（EJECTOR PIN,BLADE EJECTOR.）MULTI-FUNCTION FILTER NOZZLE. HEAT PIPE,OILLESS BEARING. 热浇道系统、温度控制器、模具零配件（射梢、强力型）万能泸嘴、测温表、自润轴承、润滑柱。
- The most sophisticated runner design is the valve gated hot runner design. 最讲究的流道是针阀式热流道设计。
- Based on analyzing hydraulic stepout and heating power stepout took place in hot water heating system indoor, the improvement plan is presented in this paper. 分析了室内热水采暖几种系统中经常出现的水力失调、热力失调问题，并提出了相应的对策意见。
- Hot runner technology for advanced automotive applications in injection molding. 热流道技术在汽车工业注塑工艺里的应用。
- The crackle of rice emerges frequently during drying by heating power. 稻谷在进行热力干燥时，往往产生爆腰现象。
- Their preform moulds could be 2-cavity based and use a hot plate or hot runner design. 模具有用两腔的，采用热板/热流道设计。
- Over two years wor experiences at simillar position. Familiar with injection rpocess(1000 t machine and hot runner tech. 2年以上同等职位工作经验，熟悉注塑工艺调试(1000吨注塑机，懂热流道技术)；
- A hot runner injection mould with interconversion installation of moving half and fixed half for a side cover was developed. 介绍了侧盖热流道动、定模反装注射模设计,应用定距拉杆以及液压缸实现了模具顺序开模和塑件的顶出,保证了产品质量。
- Use clamp ampere meter to measure the current and check if the heating power is normal. 用钳形表测量电流，检查发热功率是否正常。
- A design method of hot runner mold for PET bottle base was proposed to extend the temperature range of PET resin for better processing. 为解决PET塑料加工温度范围较窄,工艺性较差的问题,提出了PET吹塑瓶坯热流道模具设计方法。
- Semi-conductor devices have no filamentor heatersand therefore require no heating power or warmed up time. 半导体器件没有灯丝,因此不需加热功率或加热时间。
- In this dissertation, the author made a deep research on hot Runner system on the basis of a detail discussion and study of CACD technology and completed a CACD softwa. 本文从概念设计角度出发,对热流道计算机辅助概念设计技术进行了探讨和研究,实现了从概念草图到详细结构设计的计算机辅助设计过程。
- Semiconductor devices have no filament or heaters and therefore require no heating power or warm-up time. 半导体器件没有灯丝,因此也不需加热功率或加热时间。
- Comparison and contrast were made between a hot runner injection mould and an ordinary sprue runner injection mould for sortable garbage bin base used indoors. 对分类垃圾桶底座热流道注射模与普通流道注射模进行了比较,并对热流道系统设计过程进行了分析,对其计算和结构进行了探讨。
- In this paper, we introduce DCS and FCS, the application of DCS and FCS in heat power plant is mainly analyzed. 摘要简要介绍了集散控制系统和现场总线控制系统及其在火电厂中的应用，并做进一步的分析。
- This paper introduces a Pulse-Density-Modulated (PDM) load resonant induction heating power based on DSP. 介绍了基于数字信号处理器(DSP)设计的PDM(Pulse鄄Density鄄Modulation)负载谐振式感应加热电源。
- The value of static shield reaches above 40 dB, and the heating power of the paint in water is about 7 W/cm 2. 经计算 ,该种涂层是一种优良的静电屏蔽和导静电材料 ,电磁屏蔽效能达 40 d B以上 ,水中加热功率密度达到 7W/ cm2左右。
