您要查找的是不是:
- Hydrogen Injection Timing 喷氢正时
- Hydrogen injection and scramjet ignition testing. 氢注入及冲压点火测试。
- Checking of each cylinder injection timing with static. 静态检查各缸供油时间。
- At any given element spacing, the minimum stable operating hydrogen injection temperature varied linearly with face coverage. 对于任何给定的单元间距,稳定工作的最低氢喷射温度随喷注面覆盖而线性地变化。
- The desirability of providing a high hydrogen injection velocity and a low oxygen injection velocity has been previously discussed. 上面已经讨论过,希望能够提供高的氢喷射速度和低的氧喷射速度。
- In agreement with this concept is the additional experimental result that decreasing the mean hydrogen injection velocity increases the stability limit temperature. 这一概念是与补充试验的结果相符的,即降低氢的平均喷射速度使稳定性极限温度增加。
- These sensors establish ignition and fuel injection timing, and monitor crankshaft speed variation. 这些传感器(的信号)来对点火、燃油喷射定时和曲轴速度变化监控。
- The factors influencing injection timing of electronic controlled sequential injection CNG engine are analyzed. 摘要从理论上分析了影响电控顺序喷射CNG发动机喷射定时的因素及其影响特点。
- Right here the MKB software calculates the perfect injection time, duration and boost pressure. 就在这里,MKB软件精确计算燃油喷射点、持续时间及喷射压力。
- Effects of fuel injection timing on combustion and emission characteristics of a single-cylinder diesel engine fuelled with diesel and diesel-propane blends were studied. 在一台单缸直喷式柴油机上开展了不同喷油提前角下燃用柴油和柴油-丙烷混合燃料时的燃烧和排放特性研究。
- Usually, soybean oils need hydrogen injections to stay stable in high heat, such as in a fast food fryer. 通常,豆油需要经过氢化处理才能在油炸速食等高温食品中保持稳定性。
- After hydrogen injecting,firstly,a combustion flow pattern developed in the combustion chamber with the flow velocity being supersonic on average. 注入氢后,首先在燃烧室内形成平均流速是超声速的燃烧流动。
- Based on the numeric analysis of the model, the effects of melt temperature, injection time, mold temperature and pre-filled volume on the cell size were studied especially. 在对该数学模型进行数值分析的基础上,着重研究了熔体温度、注塑时间、模具温度、初始填充量对微泡尺寸的影响。
- This model took the parameters of engine speed, fuel pump rack position, pedal, LPG injection time, cooling water temperature and torque as the input variables. 模型将转速、油泵齿条位置、油门开度、LPG喷气时间、冷却水温度、转矩作为输入变量。
- hydrogen injection advanced angle 喷氢提前角
- Longer residue time (5-7 days) reduce injection time. 3-5 injection times is one cause. 更长的体内存留时间,长达5-7天,从而减少注射次数,3-5次注射为一疗程。
- Water contains hydrogen and oxygen. 水含有氢和氧。
- The dynam ometer test results showed that the injection timing had a large effect on the f uel consumption and it must be accurately and precisely controlled,when the engi ne was working at low load. 试验表明:喷油时刻对于降低燃油消耗率影响很大,小负荷时必须对喷油时刻进行精确控制;
- The hepatitis B-BCG combined vaccine can decrease injection times and reduce adverse side effects. 制备乙型肝炎-卡介苗联合疫苗,可以减少针次,降低副作用。
- In this study, the conditions of CZE, such as running voltage, running temperature, injection pressure,injection time and the components of the buffer solutions were examined in detail. 详细考察了电泳分离参数,包括缓冲剂种类、缓冲溶液添加剂、分离电压、运行温度等的影响。