该词条未找到_海词词典

您要查找的是不是：

Motor half coupling lock nut 电动机半联轴器的锁紧螺母
Pump half coupling lock nut 泵联轴器的锁紧螺母
Install adjuster nut and lock nut. 安装调节器螺母和防松螺母。
Lock handle securely by turning lock nut clockwise. 3、顺时针方向拧紧螺帽，可靠的锁好把手。
To Readjust- Loosen lock nut on the adjusting screw. 重新调节：松开调节螺丝上的锁定螺母。
To Readjust - Loosen lock nut on the adjusting screw. 重新调节：松开调节螺丝上的锁定螺母。
Revolving the lock nut 5 anti-clockwise to the suitable position. 逆时针方向旋转锁紧螺母5;使其退到适当位置.
Disc is fastened securely to disc hanger with a lock nut and cotter pin. 通过一个锁紧螺母和开口销将阀瓣安全紧固在阀瓣支架上。
Diesel engine is connected with half coupling through gimbal, driving pump rotator to revolve. 泵由柴油机通过万向节连接到半联轴节，驱动泵转子部件旋转。
If only one locating ring is required, it should be inserted on the same side as the lock nut. 如果只需一个定位环,此定位环应插入与锁紧螺母相同的一侧。
The first product we developed and completed based on this theme was the Hard Lock nut. 我们以此为出发点,开始了研究开发,经过不断实验终于研究成功了Hard Lock螺母。
Small bearings with a bore diameter up to 100 mm can be properly mounted by measuring the lock nut tightening angle. 孔径最大为100毫米的小型轴承可通过测量锁定螺母的紧固角度正确安装。
To replace diaphragm; loosen lock nut (48) and remove lock washer (46), diaphragm plate (60) and diaphragm (20). 要更换隔膜，先松开锁紧螺母(48)，并拆卸锁紧垫圈(46)，隔膜板(60)和隔膜(20)。
Loosen and remove the diaphragm lock nut and lock washer, pressure plate and diaphragm from the valve stem. 松开和拆卸隔膜锁紧螺母和锁紧垫圈，从阀杆上往下压阀盘和隔膜。
Remove spring cage, spring and washer. Remove bottom plug. Grasp upper and lower stem lock nut with wrench and loosen. Clean or replace any damaged or worn parts. 拆卸弹簧笼，弹簧和垫圈。拆卸底部塞。用扳手抓住上部和下部阀杆锁紧螺母并且松开。清洗或更换任何损坏或磨损部件。
Remove the locking nut from the flow/conductivity/temp sensor. 移开流量/导电/温度传感器上的固定螺丝。
Remove the locking nut from the flow / conductivity / temp sensor. 卸除流量/电导/温度传感器上的锁紧螺帽。
No male/female assembly is requested and both half couplings are iden ti cal, making main te nance and logistic easier. 这里不要求确定阴组件和阳组件，因为两个半联轴节都是完全一致的，也为维护和供应提供了方便。
The feasibility of repetitive use of Fe-based shape memory alloy lock nut has been studied in order to lower the usage cost. 为了降低铁基形状记忆合金防松螺母的使用成本,探索了该新型螺母重复使用的可行性。
Measuring the lock nut tightening angle is a proven method to determine the correct degree of interference in small to medium-sized bearings on tapered seatings (fig). 测量锁定螺母的紧固角是经验证的有效方法,可用来确定圆锥轴颈上中小型轴承的正确过盈度(图17)。