您要查找的是不是：
- Rear axle sleeve press machine 半轴套管压机
- Rough boring machine for rear axle sleev 桥壳套管孔粗镗
- The rear axle carries the greatest weight. 后轴负荷最重的分量。
- Han Yingchun, Wang Xueming, Chen Yubao. The new technology of the forward extrusion and cross rolling for the rear axle shaft sleeve of light truck. Germany： 6th ICTP, 1999. 韩英淳;王学明;陈义宝等.;“农用运输车正挤与横轧式后桥半轴套管”发明专利
- A pole connecting the rear axle of a vehicle with the front. 连接杆连接车辆前后轴的杆
- Front axle moved forward 60mm, rear axle moved backwards 20mm. 前桥前移 60 厚米，后桥后移 20 毫米。
- We had a lot of bother in repairing the press machine. 修理这台印刷机费了很大劲。
- The rear axle is stationary, and is bolted rigidly to the main frame. 后轴是固定的，用螺栓刚性固定在主机架上。
- The alloy is suitable for making wear resistant parts such as bush, axle sleeve and worm wheel etc. undor the conditions of high and middle load at the middle and low speed. 合金主要用于制作高、中载,中低速不同工况条件下工作的轴瓦、轴套、蜗轮等耐磨件。
- In order to solve the problem of difficult circumferential lateral pulling, a special structure of injection mould for the axle sleeve is designed. 针对轴套圆周方向侧向抽芯较难的问题,设计了一种特殊的轴套注塑模具。
- The surface craze of 20 steel axle sleeve in free forging was analyzed by chemical ,spectrum and miscrostructure analysis. 采用化学分析、金相检验、光谱分析等方法对20钢轴套的自由锻件表面产生的龟裂进行了分析。
- Rolled steel axle sleeve uses structural treatment, the public errand of axial aperture, verticality, coaxial spends allow difference to all be in 0.01 in. 钢板轴套使用构架处理;轴孔的公差、笔直度、同轴度允差均在0.;01之中。
- Company specialize in automobile fittings, sandy beach car rear axle always succeeding and auxiliary products. 公司专业生产汽车配件及其配套产品。
- Guangzhou Yiu Wing Pressing Machine Co., Ltd. 广州耀荣整烫机械有限公司。
- The bike chain drives a sun gear on the rear axle, which transmits power to planetary gears situated around it. 自行车的链条会驱动后轮轮轴上的太阳齿轮，将动力传送到四周的行星齿轮。
- The reason the propeller shaft shortens as the angle increases is that the rear axle and differential move in a shorter arc than the propeller shaft. 当角度增加时,传动轴变短的原因是后桥和差速器运动的弧度小于传动轴运动的弧度。
- At last, design a set of dimensions of balancing mechanism as a balancer for a press machine. 最后并以实际冲床为例，设计一动平衡机构。
- The rack-and-pinion steering is sharp, and the torsion beam rear axle gives the car a grown-up feel. 齿条式齿轮转向是敏锐的，而尾轴扭力梁给车子有大车的感觉。
- Shaped part: board molding machine, paper adjustor, press machine, shaped flat table and shaking motor. 成形部分：以板式成型机为主，外加调纸机、压合器、成形平台及震动电机组成。
- The strength, stiffness and mode shape of the rear axle housing was calculated via finite elemant methool (FEM). 根据计算结果分析，指出了其结构存在的缺点，提出了改进方案。
