您要查找的是不是：
- Welded Seam Strength 焊缝强度
- Research on Adopting the Slim and Double Welding Rods to Improve the Weld Seam Strength and Toughness Matched Together 用细丝双丝双弧焊改善焊缝强韧匹配的研究
- The welded seam of one stiffener on bulwark in way of std frame No.66 broken. 如：连接甲板与舵角限制器三角板的焊缝断裂。
- Active CO2 gas cylinder used specific welding machine , weld seam forming aesthetic, high strength. 活柱体采用CO2气体保护焊专用焊机，焊缝成形美观，强度高。
- It illustrated the importance and the bright prospect of the application of the automatic weld seam tracking in EBW. 分析了其组成、原理及其在实际生产中的应用,阐述了焊缝自动跟踪技术在电子束焊接中的重要性及其应用前景。
- The final choice would depend on fabric thickness, type of garment and required seam strength. 最终选用什么线应根据面料的厚度、服装的款式以及线缝所要求的牢度而定。
- Study showed that angle deformation of T joint is changed along the welded seam length. 研究表明,T形接头的角变形沿焊缝长度方向是变化的。
- Welded seam is not straight caused by adhesion sides ,require factory reinspection and rework. "热压模线内侧粘边,造成模线不线,要求重新检查返工"译成如下是否可以:
- By the test, the paper draws the conclusion that seam kind, seam width, stitch density and stitch kind have effect on seam strength. 通过实验分析，得出缝型、缝宽、针迹密度及线迹类型等因素对缝口开裂强度的影响。
- Meanwhile the welded seam corrosion-resistance property of EBW of AA8009 alloy is better than that of TIG. 同时,AA8009合金电子束焊缝的抗蚀性要明显优于氩弧焊的抗蚀性。
- A welded seam tracing system of three-dimensional visual sensor based on the structure light is designed. 摘要研制了一套基于结构光三维视觉传感器的焊缝自动跟踪系统。
- Repair for Crack on Weld Seam in No.2 Oxygen Ball Pot of Laiwu Iron and Steel Co., Ltd. 莱钢2%23氧气球罐焊缝裂纹的修复。
- The article analyzes that all factors effect impacting toughness of welded seam of ERW pipe on the basis of mass produce and practice. 在大量生产实践的基础上分析了影响ERW直缝电阻焊钢管焊缝冲击韧性的各种因素。
- Inspection welding seam and dimension of cargo hatch cover. 货舱舱口盖焊缝和尺度检查。
- The striation spacing in heat affect zone and welded seam samples was wider than that in matrix sample,this shows that fatigue crack propagation... 焊缝区和热影响区试样的辉纹间距较基体区的大,说明裂纹扩展速率快,焊缝和热影响区的抗裂纹扩展性较基体差。
- The paper described the reliable weld seam tracking system based on dynamic mask match for spirally tubes. 摘要设计一种基于动态模板匹配的焊缝自动跟踪系统。
- Inspecting welding seam of hatch coaming after welding. 货舱口围板焊接后焊缝检查。
- It analyses quadratic phase stainless and its metal compound generated from weld seam and HAZ,which affect welded pipe usage property. 分析了双相不锈钢及其焊缝和热影响区中产生的金属间化合物等二次相对焊管使用性能的影响。
- A tactile sensor welding seam tracing in welding was designed. 摘要设计了一种接触式自动焊缝跟踪传感器。
- Welding seam performed in prefabrication shop denote with “S “. 在预制厂焊接的焊缝，用“S”表示。
