您要查找的是不是：
- Welding axle housing 焊接桥壳
- Remove differential case from axle housing. 从轴管上拆卸差速箱。
- Remove differential case and dummy bearings from axle housing. 拆卸轴壳内的差速箱和平衡轴承。
- Install differential case and dummy bearings in axle housing (without shims) and tighten retaining cap bolts. 在轴壳内（没有垫片）安装差速箱和模型轴承，并紧固固定帽螺栓。
- Using the programmable controller in the automobile rear axle house ring stiffener,logic sequential control was realized in the top plate automatic welding craft. 采用可编程控制器在汽车后桥壳加强环、后盖自动焊接工艺中实现逻辑顺序控制。
- The analysis provides a reliable reference for the optimal design of a hydro-bulged axle housing. 研究为液压胀形桥壳优化设计提供可靠的参考。
- The strength, stiffness and mode shape of the rear axle housing was calculated via finite elemant methool (FEM). 根据计算结果分析，指出了其结构存在的缺点，提出了改进方案。
- The analytical findings provide some referential basis for the designof a rear axle housing structure. 研究结果为桥壳结构设计提供了一定依据。
- In order to reduce gas hole defects in the rear axle housing castings,oddside venting system was used. 为解决汽车后桥外壳铸件存在的气孔缺陷,采了假型排气系统。
- Drive shafts modified for new location on the axle housing and because of the new doubler. 传动轴修改来配合分动箱放大齿轮组。
- The first axle housing type is a unitized carrier construction, commonly referred to as a Salisbury or Spicer type axle assembly. 第一桥壳型是一个单元载体建设，通常称为梳士巴利或斯派塞类型桥总成。
- There are 12 round holes circumferencially equispaced on the axle housing cast,being in need of radial multiple core pulling. 轴套铸件上有12个周向均布的圆孔,压铸生产时需要多型芯径向抽芯。
- Unitized carrier axle housing constructions of this type are economical to manufacture and are readily adaptable for a variety of vehicles. 组合承运人车轴住房建设这类经济生产，并易于适应各种车辆。
- Through the drive axle housing , the tractive force 、 braking force and lateral force act on the wheel transfer to the suspension system 、 frame or carriage. 作用在驱动车轮上的牵引力、制动力和侧向力,也是经过桥壳传到悬挂及车架或者车身上。
- Aiming at laggard and low automatization degree of clearance measure method on axial assembly clearance between half shaft assembly and rear axle housing in automotive rear axle assembly, a new type clearanceometer was developed. 针对汽车后桥总成中半轴总成与后桥壳之间轴向装配间隙测量方法落后、动化程度差等问题,开发了汽车后桥总成装配间隙测量仪。
- The 194 Rear Beam-design Iron (RBI) axle housing has an iron center casting (differential housing) with axle shaft tubes extending from either sidThe tubes are pressed into and welded to the differential housing to form a one-piece axle housing. 194后梁设计钢（RBI）轴壳有一个带有驱动轴套的钢制的中心铸件（差速壳），它延伸到两边。轴套被压进差速壳，并焊在差速壳上，形成了一个整体的轴壳。
- Main products are gray cast iron, ductile cast iron, carbon cast steel for construction machinery and high-load automobile with the no-bake resin sand process, such as axle housing, gearbox housing, hub, carrier etc. 本公司主要采用生产无箱树脂砂工艺生产工程机械、重型汽车用的铸钢件、铸铁件、球墨铸铁件、如桥壳、变速箱、轮毂、托架等铸件。
- They weld the pieces of a broken axle. 他们焊接断了的车轴。
- The allowable strength, static strength, fatigue life and load-carrying capability of hydro-bulged rear axle housing in a 0.75 t truck are analyzed using FEA software ANSYS and the variation rule of its strength is obtained. 摘要以0.;75t货车液压胀形桥壳为例，利用有限元分析软件ANSYS对其许用强度、静强度、疲劳强度（寿命）及其承载能力进行分析，得到液压胀形桥壳强度的变化规律。
- He is welding the pieces of a broken axle. 他正在焊接断了的车轴。
