您要查找的是不是：
- Loosen the adjustment screw, and adjust the length of the link rod. 请拧松调整螺丝，拔出或插入连接杆进行调整。
- Remove adjuster lever, adjuster screw and spring. 拆卸调整器杆，调整器螺丝和弹簧。
- The high step moves from under the adjusting screw. 使高点从调节螺钉下移动。
- J. Vertical Shaft Fine Adjustment Screw. 垂直杆微调螺丝.
- The adjusting screw rests on the high step of the cam. 调节螺钉落在凸轮高点上。
- Tie-Rod of Marble Gang Saw with hydraulic driven is for connecting hydraulic tensioner and saw blade. It composes of Rear Tie-Rod, adjust screw and wedge. 大理石框架锯液压锯夹用于连接液压涨紧器和锯条，它由前后锯夹，蝴蝶板、插板和调整螺杆组成。
- Tighten adjustment screw to 3 N·m (30 in-lbs) torque. 拧紧调整螺丝到3 N·m (30 in-lbs)扭力。
- To Readjust- Loosen lock nut on the adjusting screw. 重新调节：松开调节螺丝上的锁定螺母。
- Lubricate adjuster screw threads and pivot with spray lube. 使用喷雾润滑油润滑调整器螺丝螺纹和枢轴。
- To Readjust - Loosen lock nut on the adjusting screw. 重新调节：松开调节螺丝上的锁定螺母。
- Firmly screw can on adapter, and turn the flow adjustment screw. 将料罐倒置与喷枪连接，旋转打开流量阀，调节流量。
- Add fine adjust device for the pressure of foot,without dial on the adjustable screw, more convenience for operation. 压脚压力采用微调装置，压力调节螺钉设有刻度，更加方便操作。
- Remove compression from spring by turning adjusting screw (1) counterclockwise. 通过反时针方向旋转调节螺丝(1)从弹簧上拆卸压缩件。
- A pinion shaft, the rack shaft, and a rack guide holder are assembled in a housing, and an adjust screw is strongly tightened to press the rack guide holder toward the rack shaft under an overload. 齿轮轴、齿条轴和齿条导向支架安装于壳体内，并且调节螺杆在载荷作用下非常紧地将齿条导向支架压向齿条。
- Keeping well away from the propeller, adjust the engine to maximum rpm with the mixture adjustment screw marked with an "H". 跟螺旋桨保持距离;推油门全开.;转进标记"H"螺丝求取最高转速。
- Heavy duty adjusting screw. Adjusting screw is both slotted and knurled. 重型调节螺丝。调节螺丝既有槽也有花纹边。
- Adjustment of parallelity, adjust screw (6), you can set the parallelity between printing squeegee and ink-collecting squeegee. 平行度调整:调节螺丝(6),可调整刮墨刀、回油刀与丝网的平行度。
- To replace seat/ stem module shut off supply, loosen locknut and back off adjusting screw. 要更换阀座/杆模块，先关闭供应管道，松开锁紧螺母，退出调节螺丝。
- Two adjusting screws harmonise the guns with the sight. 有两个调节钮来校准武器和瞄准具。
- To replace seat/stem module shut off supply, loosen locknut and back off adjusting screw. 要更换阀座/阀杆模块，先关闭供应管道，松开锁紧螺母，退出调节螺丝。
