该词条未找到_海词词典

您要查找的是不是：

air injection pressure 空气喷射压力
Injection pressure and holding pressure i. 注射压力和保压压力。
Now air injection into light oil for EOR has received more attention. 目前注空气提高轻质原油采收率受到广泛的关注。
Injection pressure was 20 pis, 5 sec and power supply was 15kV constant. 自动气压进样;20pis;5sec.
The wax appearance temperature rose after air injection and fell when the temperature of air injection rose. 注空气后比注空气前石蜡沉积点高；注空气温度增加，石蜡沉积点降低；
Injection pressure of J-ELIII series is different from that of JSW's hydraulic machines. 注塑压力与油压系列不同。
Air injected into the powder path to atomise it into a pattern. 按照粉末路径到喷涂成型（工件）之间喷射的空气。
Maximum injection pressure and maximum holding pressure may be restricted due to molding condition. 有的情形下,最大注塑压力,最大保压压力会因成成形条件不同而受到限制。
Moreover, the principle and evaluation method of LTO process are discussed, and the developing trend of air injection is forecasted. 此外，还论述了注空气低温氧化技术的原理、评价方法等方面的内容，预测了该技术的发展趋势。
Colon hydrotherapy equipment can sustain a regulated and safe injection pressure to permit cleaning water to reach th extremities of the colon. 大肠水疗法设备能够维持一个规范和安全注射压力,让水清洗,以达到末端结肠。
As advancing of technical progress, air injection LTO process will be an inevitable trend of gas flooding both in China and the world. 随着技术进步，注空气低温氧化技术是我国乃至全世界注气提高采收率技术发展的必然趋势。
Increased needle injection pressure was obsered as the olume of PMMA increases and as the distribution of PMMA is in close proximity to the cortical walls. 同时，使用的聚甲基丙烯酸甲酯黏合剂的体积的增加还可以增大融合椎体的强度。
Experimental studies of turbulent combustion were conducted in a test facility for swirl combustor with staged air injection. 本文在分级进风旋流燃烧室的实验装置上进行了湍流燃烧的实验研究。
The pH of buffer was 6.2, and the run-voltage was 7kV. Pressure injection model was used and injection pressure was 2406.25 kPa xs. 运行电压为7kV，采用压力进样方式，进样压力为2406.;25kPa×s。
As advancing of technical progress, air injection LTO process will be an inevitable trend of gas flooding both in China a... 此外,还论述了注空气低温氧化技术的原理、评价方法等方面的内容,预测了该技术的发展趋势。
In the Common Rail accumulator injection system, the generation of the injection pressure is separate from the injection itself. 在共轨蓄压喷射系统，新一代的喷射压力是分开的，从注射本身。
The calculating formula for the plastics backface shrink pitfall value of the strengthening rib was put forward at considering the processing conditions of injection pressur... 提出了在考虑注塑压力、注射温度、注射速率等工艺条件下,塑料件加强肋背面的缩陷值的计算公式,并找出通过模具尺寸设计进行补偿的方法。
Therefore, the understanding of laboratory experiment and analytical methods, as well as matching experiment is critical to use air injection for EOR properly. 因此，了解室内实验研究内容、分析方法，以及拟合室内实验，是正确运用注空气提高原油采收率技术的关键。
The injection pressure and flow rate and the lengths of injection and falloff periods are the key factors to the succession of well test. 注入的压力、排量以及注入和压降段的时间是关系到试井成功与否的关键因素。
Results of the experiment show that the air injection has a distinct effect on fiber fractionation,and a good fractionation performance is obtained with increa... 实验结果表明,气体的充入对纤维筛分有明显的影响,随着充气量的增加筛分效果将得到改善。