您要查找的是不是：
- RAM AIR INLET MECHANICAL LINKAGE. 冲压空气进口机械连杆机构。
- Remove the air inlet hose from the throttle body and air cleaner. 从节流阀体和空气滤清器上拆下气流入口软管。
- As for the dehumidifying conditions, the condensing rate for the humid air increases with Reynolds number but decreases as the inlet temperature of cold water increases. 同时湿盘管的热传量及除湿率亦也随著冰水入口温度的降低而增加，显热比随著冰水温度的降低而减小。
- Turn off supply pressure and observe float drop to open air inlet. 关闭供应压力,观察浮子下降,因此开启空气进口。
- Check found birdstrike on radome and R engine air inlet. 雷达罩和右发进气道口有鸟击痕迹。
- Air inlet throttle valve with pneumatic actuator and positioner. 空气进气节流调节阀：带有气动定位和执行机构。
- Air systems are effective for space heating because a heat exchanger is not required and the collector inlet temperature is low throughout the day (approximately room temperature). 空气系统对于空间供热是有效的，因为热交换器是不必需的，且收集器的进口温度全天低（近似室内温度）。
- Inlet temperature, outlet temperature and drying air volume are displayed digitally. Condition setting dials and stage level control switch are located on the front panel for easy use. 入口、出口和干燥气流量数字显示,条件设定板、进程控制开关为方便使用被置于前板。
- Connect the air inlet hose to the throttle body and the air cleaner. 将空气入口软管接至节流阀体和空气滤清器。
- Check pressures and fluid inlet temperature be sure theyare within specified range. 检查流体压力和温度并取保他们在可用流体范围内。
- The sensible heat factors are found to increase with both Reynolds number and inlet temperature of cold water. 湿盘管的热传量随著入口风速与鳍片数目的增加而增加，显热比及除湿率亦随著风速增加而增大。
- The result can offer the proper inlet temperature and kinematical viscosity for spray drying. 结果：运动黏度对喷雾干燥的影响大于相对密度；
- Viscosity of pseudo-boehmite remains unchanged when inlet temperature is in certain range. 进口温度在一定范围时,产品黏度基本保持不变;
- Slowly open vent needle valve just as air inlet opens. Record differential pressure. 当空气进口开启时,慢慢开启排气针形阀。记录压差。
- Slowly open needle valve "C" bypass (yellow) just as air inlet opens. Record differential pressure. 正当空气进口打开时，慢慢开启针形阀“C”旁路（黄）。记录压差。
- The inlet temperature and internal temperature of exhaust catalyst for two-stroke moped are tested under different vehicle driving speed. 在不同车速行驶工况下对二行程轻便摩托车用尾气催化剂的入口及中心温度进行了测量与分析。
- Separation of the water supply from the air inlet is accomplished by means of a diaphragm seal. 供水与空气的隔离是通过采用隔膜密封的方法实现的。
- Next, let's make the simple panel under the air inlet that we can find on the side. 接下来，让我们作一个简单小组根据空气进说，我们能够找到对的一面。
- Atmospheric conditions can change engine performance considerably. The effects of engine inlet temperature and ambient pressure on engine performance are shown in Fig[3.14]. 大气条件可以相当的改变引擎的性能。进气温度和环境压力对发动机性能的影响列于图[3.;14]。
- Separation of the water supply from the air inlet is accomplished by means of a diaphragm seal . 水供应与空气进口的分离通过隔膜密封的方法实现。
