您要查找的是不是：
- arc melting metal powder 电弧熔化用的金属
- Appearance:Pure grey metal powder. 外观:纯灰色金属粉末。
- A Brief Introduction to Canadian Quebec Metal Powder Company Ltd. 加拿大魁北克金属粉末有限公司简介
- The oxidation of Zr(Fe,Cr)_2 with different Fe/Cr ratio prepared by non-consumable arc melting is carried out in air at 773K and 973K. 用非自耗电弧炉熔炼了比值(重量比值)不同的Zr(Fe,Cr)_2,并在773K和973K的空气中氧化。
- Al-base cored wires were prepared by using Al-strip to wrap metal powder, and their parameters for arc spraying process have been optimized. Typical layered Al-base coatings were fabricated. 采用Al 带包裹金属粉成功制备了铝基粉芯丝材,对其电弧喷涂工艺进行了优化,得到了孔隙率较低的优化喷涂工艺参数,成功制备出了具有典型层状结构的铝基涂层。
- In factories,workers use it to melt metals. 在工厂，工人们用火去融化金属。
- Base on this, in this work we prepared in situ TiC or (TiB+TiC)/Ti-1100 composites with various volume fraction of reinforcements by the consumable vacuum arc melting. 主要研究结果如下:在所制备的原位自生(TiB+TiC)或TiC/ Ti-1100复合材料中,增强体TiB、TiC分布均匀,与基体界面洁净,没有明显反应层存在。
- Molten metal is poured back into the moulds. 已熔的金属被倒回注入到铸模里。
- TiC reinforced titanium matrix composites were simply produced at low cost by non consumable arc melting technology utilizing the reaction between titanium and graphite. 利用钛与碳之间的反应 ;经非自耗电弧熔炼工艺 ;简洁、低成本地制备了 Ti C增强的钛基复合材料 .
- The molten metal channels into the troughs. 熔化的金属液流入槽中。
- The molten metal was run into a mould. 熔化的金属被倒进模内。
- LIANG Shu-hua, FAN Zhi-kang, HU Rui.Microstructure and properties of CuCr series pseudobinary alloy by arc melting[J].Special Casting &Nonferrous Alloys, 2004,4(25):25-27. [4]梁淑华;范志康;胡锐.;电弧熔炼法制造CuCr触头材料的组织与性能[J]
- The main products are oil quality filter, filter melt, metal powder sintering filters, polypropylene filter powder sintering, filament-wound filter, filter pipes, gas filter, filter, and other chip. 主要产品有油质滤芯、熔体滤芯、金属粉末烧结滤芯、聚丙烯粉末烧结滤芯、纤维缠绕滤芯、管道滤芯、气体滤芯、片式滤芯等。
- They poured the molten metal into molds. 他们把熔化了的金属浇灌到模子里。
- Molten metal ran out on to the flagstones. 熔化的金属溢流到外面的板石上。
- The molten metal was run into a mould . 熔化的金属被倒进模内。
- TiB and TiC reinforced titanium matrix composites have been produced by non consumable arc melting technology utilizing the self propagation high temperature synthesis reactions between titanium and B 4C, graphite. 利用钛与碳化硼及石墨之间的自蔓燃高温合成反应 ,经非自耗电弧熔炼工艺制备了 Ti B晶须和 Ti C粒子混杂增强的钛基复合材料。
- They ran the molten metal into a mould. 他们把融化的金属倒进模子里。
- The peak of temperature is more high with metal powder, as a result of absorptivity is more high. 添加金属粉末时，材料表面对激光的吸收率增强，同一测量点的峰值温度升高。
- Melted metal is poured into a mold to harden into shape. 熔化之金属倒入模子中以冷却成形。
