您要查找的是不是：
- front wheel bearing nut lock washer 前轮毂轴承螺帽锁紧垫圈
- bearing nut lock washer 轴承锁紧螺帽垫圈
- nut lock washer 螺母锁紧垫圈
- To replace diaphragm; loosen lock nut (48) and remove lock washer (46), diaphragm plate (60) and diaphragm (20). 要更换隔膜，先松开锁紧螺母(48)，并拆卸锁紧垫圈(46)，隔膜板(60)和隔膜(20)。
- Hold stem (27) on wrench flats and remove nut (51), lock washer (46), diaphragm plate (60) and diaphragm. 在扳手的平面上握住阀杆(27)并拆卸螺母(51)，锁紧垫圈(46)，隔膜板(60)和隔膜。
- Loosen and remove the diaphragm lock nut and lock washer, pressure plate and diaphragm from the valve stem. 松开和拆卸隔膜锁紧螺母和锁紧垫圈，从阀杆上往下压阀盘和隔膜。
- Disassemble module. Use wrench to loosen stem nut and remove lock washer and diaphragm plate. Remove yoke by loosening disc holder using a screw driver. 拆卸模块。使用扳手松开阀杆螺母，并且拆卸锁紧垫圈和隔膜板。采用螺丝刀，通过松开阀瓣支架来拆卸轭架。
- Early lock washer on left, as used on the 600 series. 左边是早期的固定垫圈，使用在600系列上。
- Smaller sizes use a lock nut with a locking washer (a), larger sizes use a nut with locking clip (b). 小尺寸轴承使用带锁紧垫圈的锁紧螺母(a)大尺寸的轴承使用带锁紧卡箍的锁紧螺母(b)。
- Nut locks on gate to prevent jamming. 套管锁定在栏门阻止阻塞。
- steering gear adjusting nut lock 转向齿轮调整螺母保险
- Front Stub Axle To Hub Bearing Nut 前螺桩轴至轮毂轴承螺帽
- The thread flameproof structure adopts double nut locked leading-in cable structure.The fan cowls are steel plate structure with shield barrier. 风罩为钢板结构并设有防护栅栏，与机座配合部位设有轴向限位措施，防止轴向外力冲击。
- Single coil spring lock washer for assembly 组合件用弹簧垫圈
- lock washer with tongue at outside 外舌止动垫圈
- "It appears the wheel nut locking mechanism failed so that when the gunman went to get the wheel nut off it wouldn't come off because of the mechanism," explained Whitmarsh. “最后，他干得非常棒。因为他更换了另一把枪并且不得不卸下轮毂罩，备用枪可能剪平了那两个锁定销，使轮胎得以卸下。”
- "Only wait till my time comes," he said; "I shall do more than grow roses, bear nuts,or give milk,like the hazel-bush,the cows and the sheep. "等着，等轮到我吧！"他说道，"我不止开花，不止结榛子，或者说像牛羊一样只产奶，我要贡献更多的东西。"
- Hangzhou Zhengda Spring Lock Washer Co., Ltd 杭州正大弹簧垫圈有限公司
- Serrated lock washer external teeth for assembly 组合件用外锯齿锁紧垫圈
- lock washer with tongue at inside 内舌止动垫圈
