您要查找的是不是:
- bearing oil hole 轴承油孔
- Forced lubrication for the pump, start the pump to the bearing oil. 对于强制润滑的泵,启动油泵向各轴承供油。
- Oil may be forced out through the timing cover and rear-main bearing oil seals. 机油会从正时齿轮盖和后主轴承油封处压出。
- There is one oil groove in the bronze bushing, where lubricant can flow into the axis from the oil hole on the cap of housings. 轴瓦内表面的不承担载荷部分开有油槽,润滑油通过进油孔和邮沟流进间隙。
- The oil hole is small and deep, so it is very difficult to machining. and we will try to take the broken aiguille out, and end it as soon. 因为油孔又小又深,加工难度本身很大,我方将尽快把断在里面钻头取出来就算完工。
- The fracture of stuffing box was caused by fatigue, which resulted from the maximum stress concentration on the centripetal border of the oil hole. 结果表明:材料成分和显微组织均符合要求;裂纹起源于输油孔的侧壁;填料盘的失效模式为疲劳失效,内压在填料盘内部输油孔上产生的应力集中导致了填料盘的疲劳失效。
- Install the new upper rear bearing oil seal with the white paint facing towards the rear of the engine. 安装新的上后轴承油封,使白漆面向引擎后部。
- ARE THE FAULTS CONTROLLING MESO-CENOZOIC BEARING OIL AND GAS BASINS IN EASTERN CHINA TENSILE FRACTURES? 中国东部某些中、新生代含油气盆地与部分北东向正断层成因分析?
- A kind of Rotary cultivator shell, it includes shell with transmission shaft axis hole and set oil hole, set oil hole end has end cover , magnet is in this end cover . 一种旋耕机机壳,它包括带有传动轴轴孔及放油孔的壳体,放油孔端头设有端盖,在该端盖内设有磁铁。
- Use of the bearing oil leak detector will determine whether or not bearing wear has been uneven. 使用漏油检测装置即可判定轴承磨损是否均匀。
- This article introduces mainly calculation of a slanting angle of crankshaft clamping with the analysis method in machining crankshaft oblique oil hole. 主要介绍在加工发动机曲轴斜油孔时,用解析法计算曲轴装夹时所倾斜的角度。
- The Bearing oil L-FD68 were formulated from base oil obtained by deep-refining paraffinic crude and doped with various additives. 以深度精制的石蜡基馏分油为基础油,添加了各种添加剂,制备了轴承油L-FD68。
- The test results show that the antifriction film bearing oil # 100 meets the necessity of using in high speed thread milling machine and under the serious working condition. 试验表明兰炼100号抗磨型油膜轴承油完全可以满足高速线材轧机精轧机组特殊工况的使用要求。
- But there are inherent heat losses associated with long wellbore and heating surrounding rock formations that do not bear oil, so OSR is little and recovery efficiency is low. 但长井筒的热损失以及加热不含油岩层的热损失导致油汽比小 ,采收率低。克服热损失问题的一种潜在方法是用溶剂替代蒸汽。该方法称之为溶剂蒸气抽提法。
- Improvement in Piston Pin Boss Oil Hole Machining 活塞销座油孔加工方法改进
- Owing to the good adhere ability, hydrophobility and bearing oil ability of PDMS, the contrast of brightness of the pixel unit is realized, by successfully controlling the outspreading and shrinking of the oil droplet in the simplified structure. 利用具有良好黏合性、水性和耐油性的PDMS(二甲基硅氧烷)料,研制了结构精简的反射型显示单元,成功地控制了显示单元中油滴的扩张与收缩,实现了像素单元对比度的变化。
- steering column jacket oil hole cover 转向轴套油孔盖
- Provide manufacture services of rubber-ware pressing process machine, roller bearing oiling, rubber-ware grinding and cutting. 提供皮棍压套罗拉轴承加油皮棍磨削加工服务。
- FAW TOYOTA engine company crankshaft product line uses carbide tool and MQL technique to process crankshaft oil holes. 一汽丰田(长春)发动机有限公司曲轴生产线采用硬质合金钻头并配合半干式加工(MQL)技术加工曲轴油孔。
- Research on location of the distribution oil hole 配油孔定位研究