您要查找的是不是：
- TUBE DIAMETER SHALL BE WITHIN 10% OF NOMINAL DIAMETER WITHIN BEND RADIUS. 管直径须在直径理论值和折弯半径的10%25以内。
- The temerature not less than O℃ and recommended bend radius not less than6 times of outer dia. 电缆适用于管道地埋及架空敷设，不能承受机械外力作用。
- Bend radius of the bottom cover will need to be made smaller so that the two parts of the unit fit together correctly. 底盖的半径要改小一些，以便该产品的两个部分正确地合在一起。
- Cycle Life Corrugated metal hose bend radius and minimum acceptable cycle life design requirements are outlined. 循环寿命-波纹金属软管的弯曲半径和可接受的最低寿命周期设计的大纲要求。
- By analyzing the simulation results, how the hardening parameter, bend radius parameter and thickness parameter influence springback is studied. 通过对模拟结果的分析，研究了硬化指数、弯曲半径、材料厚度等因素对回弹的影响规律。
- The formulae for calculating the bend radius of neutral plane and the decrement of bend angle after springback were derived by considering the deformation after unloading. 依据卸载变形的分析计算，推导出回弹后中性层弯曲半径及弯曲角变化量的计算公式。
- The bending radius of the hose fitting should not be too small. 软管接头部位转弯不要过小,应大于软管内经8倍以上。
- The bending radius should not less than 15 times of cable diameter. 电缆弯曲半径:不小于电缆外径的15倍。
- The bending radius should not be less than 25 times of the cable diameter. 电缆弯曲半径：不小于电缆外径的25倍。
- Feature: Anti-bending of hose body, small bending radius, good stiffness, with or without metal fittings available. 特性:管体耐曲挠、弯曲半径小、挺性好。带或不带金属接头。
- Values and test criteria for meeting static and dynamic bend radii are also listed. 符合静态和动态弯曲半径的测试标准也已列出。
- Allowed bending radius not smaller than 6 times of its outer diameter, laying temperature not lower than 0. 电缆允许弯曲关径应不小于电缆外径的6倍,敷设温度应不低于0。
- The bending radius of a cable should not be less than 10 times of the cable diameter. 电缆弯曲半径不小于电缆外径10倍。
- The bending radius reduces with increasing length of the mainstream line, and then tends to be relatively stable. 随主流线长度增加，弯曲半径不会无限制减小，将会趋于某一相对稳定状态；
- Excellent pliability, flexibility and elasticity and suitable for special occasions requiring small bending radius. 本产品具有极好的弯曲、柔软性和弹性,可用于弯曲半径较小的场合。
- Permissive bending radius of cable should be no less than 20 times of external diameter of cable. 3电缆的允许弯曲半径不小于电缆外径的20倍。
- Small bending radius, simplified busbar framework, clear arrangement, easy mounting. 弯曲半径小，母线架构简明，布置清晰，安装方便。
- The stream takes a sudden bend to the east. 小溪突然转向东流。
- Excellent pliability，flexibility and elasticity and suitable for special occasions requiring small bending radius. 本产品具有极好的弯曲、柔软性和弹性，可用于弯曲半径较小的场合。
- For the same amount of bending angle, the springback increase linearly with the increase of bending radius. 对于一定的弯曲角度，零件端部回弹量随弯曲半径的增加而线性增加；
