您要查找的是不是：
- clearance between poles 极间隙
- The clearance between the needle and the hook point is too large. 机针和旋梭尖的间隙过大。
- The clearance between the two cars was only ten centimeters. 两辆汽车间的距离只有10公分。
- Measuring clearance between propeller shaft &bearing. 螺旋桨轴与轴承间隙测量。
- It is because of the big clearance between the brake facings? 是不是因为刹车片之间的间隙太大了？
- And, the cooling flow rate of the clearance between stator and rotor as well as the hole of rotor flange was obtained. 获得了静盘与转盘间隙以及转盘外缘小孔的冷气流量。
- Small clearances between vital parts. 在活动部件之间的间隙很小。
- Or in the balcony horn establishs perpendicular pole outside, setting upright the ligature between pole pole or pull a string, form the thing of kind of barrier. 或在阳台的外边角立竖竿，并在竖竿间缚竿或牵绳，形成类栅栏的东西。
- The Clearance between glue roller and meter roller is controlled by electric mirco-adjustment and digital indication. 上浆辊与减浆辊之间隙以电动微调,并附数值显示。
- Problems include water in the pipe and lack of clearance between inner and outer pipe walls. 问题包括管中有水以及在内管和外管之间缺乏清洁。
- Thigh clearance between the slider and the seam edge causing slider to operate with difficulty. 拉链牙与布边的距离太近,导致拉链拉合有困难。
- The effective methods for low voltage of electrolyzer were that power consumption and distances between poles were decreased, and voltage drop between solutions of poles was reduced. 为了获得低的槽电压从而降低电耗,缩短电极间的距离,减少电极间溶液的电压降是非常有效的方法。
- Clearance between shearing blades adjusted by hand wheel to be quicq, accurate and convenient. 刀片间隙由手动轮调整,迅速、准确、方便。
- The clearance between the beating roll and bedplate in a ZDC beating engine is very important for its functioning. ZDC打浆机飞刀辊与底刀之间的间隙,对打浆机的性能有着重要的影响。
- Check the alignment of the piston by measuring the clearance between the piston and the cylinder. 通过测量活塞与缸套之间的间隙来检查活塞的对中情况。
- This helps eliminate any clearance between the mating surfaces of the spindle and tooling shank. 程序的格式和语言是根据机床硬件设备和微控制器来决定的。
- Sporogenous cells were vacuolated, misshapen, stretched-out and the clearance between cells was enlarged. 结果发现：败育现象从造孢细胞时期以后每个阶段都有发生，败育形式有造孢细胞液泡化、畸形、拉长、细胞间隙大；
- Clearance between punches and cutting sections should reflect the following unless otherwise specified. 除非其它说明,冲头及下模入子之间的间隙应遵循以下标准。
- The clearance between plunger and barrel of a pump is a key parameter for the pump. 抽油泵的泵隙是抽油泵的一个重要技术参数。
- In this way, the clearance between the countertop and the wall can be eliminated to an extent. 可一定程度上消除较大的台面靠墙缝隙。
