您要查找的是不是：
- clutch cover plate 离合器盖板
- Position clutch cover over disc and on flywheel. 把离合器盖板放在离合器片和飞轮上。
- XXX Co., Ltd. is specialized in manufacturing the Clutch plate and clutch cover. XXX有限公司是专业生产汽车离合器从动器钢片和压盘的企业。
- The injection mould for a duplicator cover plate is designed. 设计了复印机盖板的注塑模具。
- Reattach cover plate to make an air and water tight seal. 重新固定盖板，并紧密密封防止空气和水通过。
- Bolted cover plate to protect seal and cylinder from the ingress of debris. 上盖板可防止杂物进入缸筒损坏密封。
- If original clutch cover will be reinstalled, mark position of cover on flywheel for assembly referencUse paint or scribe for this purpose. 如果安装原来的离合器盖板，在飞轮上标记盖板的位置，以便于参考。用油漆或划线来完成此工作。
- Disconnect the hose from the bottom cover plate to the relief valve. 断开底部盖板到安全阀上的软管。
- If original clutch cover will be reinstalled, mark position of cover on flywheel for assembly referencUse paint or a scriber for this purpose. 如想重新安装原盖，则用油漆或划线器在飞轮上标记盖位，作为装配基准。
- Lightweight magnesium valve covers, ignition cover, and sound deadening plastic outer clutch cover. 轻量化的镀镁气门，带盖的点火开关，离合器外部有一个消音塑胶盖子。
- Remove the cover plate of the relief valve by removing the four connecting screws. 通过拆卸四个连接螺丝来拆卸安全阀盖板。
- Remove clutch cover and disc. 拆下离合器盖和片。
- If you open the cover plate of your cell phone, you'll see a rectangular LCD on its backside. 把手机的盖板打开来,背面就是一整片长方形的液晶萤幕。
- Fuji Industry Co.,Ltd is a leading worldwide manufacture &exporter of clutch disc, clutch cover assembly &clutch facing and disc pad, We can supply to your needs for all Japanese, European, American vehicles, trucks. 该公司主要出口产品有离合器压盘;离合器盖;刹车片;适用于所有日本;欧洲;美国小车;卡车.
- Before installing cover plate, a continuity test should be performed to assure that switches are properly set. 在安装盖板之前,应该进行断路检查测试,以确保开关正确设置。
- Adjust the Mounting Bracket so that the Sensor sits flush against the Cover Plate. 请调整安装架使得感应器与盖板处于合适的位置。
- Fitting 272 has an opening 274 therethrough that communicates with channel 266 and recess 264 in cover plate 262. 管接头272有一通道274经过，连通盖板262上的通道266与凹处264。
- General Assembly Table of Clutch Cover and Pressure Plate Assembly 盖及压盘总成总装台
- Slowly open all ball valves to relieve air and water pressure. Loosen bolts on groove coupler and remove groove coupler and cover plate from valve body. 慢慢开启所有球阀，释放空气和水压力。松懈沟槽状联结器上的螺栓，从阀体上拆卸沟槽状联结器和阀盖板。
- Slowly open all ball valves to relieve air and water pressure. Loosen bolts on groove coupler and remove groove couple and cover plate from valve body. 慢慢开启所有球阀,释放空气和水的压力。松开沟槽连接器上的螺栓,从阀体上拆卸沟槽连接器和盖板。
