您要查找的是不是：
- control variable technique 控制变量技术
- When the event handler ends, it sets the control variable back to zero. 事件处理程序在结束时将控制变量设置回零。
- It depends on measurement of controlled variable. 它取决于控制变量的测量。
- It uses a loop control variable, also called a counter, to keep track of the repetitions. 它使用循环控制变量(也称为“计数器”)跟踪重复。
- If the return value is zero, the control variable has been set to 1 and the event handler proceeds. 如果返回值为零,则此控制变量已被设置为1并且事件处理程序继续进行。
- You specify the loop control variable, but you do not have to determine starting or ending values for it. 您指定循环控制变量,但不必确定它的起始值或终止值。
- Array declared as for loop control variable cannot be declared with an initial size. 声明用于循环控制变量的数组时不能使用初始大小的值。
- Periodic change imposed on a controlled variable or a function by a controller. 通过控制器控制某一变量或函数进行周期性变化。
- Control variable was introduced in EWF_net for describing the relevant data of workflow model. EWF_net通过引入控制变量来描述工作流模型的相关数据信息;
- The reliability indices, optimal diagnostic critical value and optimal check cycle are derived by using the probability analysis, the supplementary variable technique and an optimization method. 利用概率分析、补充变量和最优化方法，求出了系统基于可靠性的最优诊断参数临界值和最优检测周期。
- Using supplemen-tary variable technique in stochastic models, a multi-dimensional Markov process including the queueing process in the queue mentioned here as a component is constructed. 该系统的瞬时队长过程一般不是一个马尔可夫过程,难于直接求取它的分布。
- The event handler uses the CompareExchange(Int32, Int32, Int32) method to set a control variable to 1, but only if the value is currently zero. 事件处理程序使用CompareExchange(Int32,Int32,Int32)方法将一个控制变量设置为1,但仅在此变量的当前值为零时才进行此设置。
- Based on Petri nets,control variable was added to DWF_net and transition was classified as transition entry and transition body. 工作流描述模型在Petri网的基础上增加了控制变量,并将变迁划分为变迁入口和变迁体两部分。
- The control thread uses the CompareExchange(Int32, Int32, Int32) method to set the control variable to -1 (minus one), but only if the value is currently zero. 控制线程使用CompareExchange(Int32,Int32,Int32)方法将控制变量设置为-1(负一),但仅在此变量的当前值为零时才进行此设置。
- The optimal control variable was gained according to the PMP, the start time, end time and switch time of conflict resolution were obtained by inner-point restriction condition. 采用极小值原理解得最优控制变量,并由内点约束条件获得解脱开始时间、约束时间及控制变量转换时间。
- By using the exhaust gas temperature deviation of the middle windbox as the feedforward input, the feedforward control variable is obtained through fuzzy alogrithm. 以中部风箱废气温度变化为前馈输入,通过模糊算法得到前馈控制量。
- Based on optimal control theory,we studied gliding control of guided bombs for optimizing a certain type of performance index with constraints on control variable and end states. 结合最优控制理论,研究了控制变量和末端状态均有约束的条件下,为了满足某个性能指标最优的要求,制导炸弹的滑翔控制问题。
- supplementary variable technique 增补变量法
- Applying stochastic control principle and a dynamic inventory model of supply chain with multi-distributed center based on literature(superscript [1]), the bullwhip effect is restrained by taking the order as control variable. 本文采用随机控制理论方法，针对在文[1]基础上建立的具有多分销中心的供应链动态库存模型，以供应链系统中的订货作为控制变量抑制牛鞭效应。
- Specially designed air box features a solenoid controlled variable intake to provide excellent throttle response. 特别设计的空气中采用了可变进气控制电磁阀提供优质的油门反应。The inlet duct is forward facing.;入口管具有前瞻性面临。
