您要查找的是不是：
- Critical compression stress is an important index to evaluate the compression properties of paper honeycombs. 纸蜂窝面外压缩临界应力是评估纸蜂窝承压性能的一个重要指标。
- critical compressive stress 临界压应力,临界压缩应力
- Critical Compression Stress Evaluation for Paper Honeycombs 纸蜂窝压缩临界应力经验评估
- The compressive stress of general polyamine soft foam plastic is improved with polymer polybasic alcohol . 为了改善普通聚氨酯软泡的压陷性能,采用添加聚合物多元醇,并对照其添加前后的物性。
- The results show that the critical compressive strength of zigzag BN nanotube is bigger than that of armchair BN nanotube with same size, which is consistent with carbon nanotube. 结果表明，同尺寸的锯齿型氮化硼纳米管的临界轴向压缩强度高于扶手型氮化硼纳米管，这与碳纳米管的研究结果一致。
- Compressive stress is transferred by carrying plate and PBL (Perfo-Bond Leisten) shear connectors. 压应力由承压板及PBL剪力键共同传递，拉应力、剪应力主要由PBL，剪力键传递。
- The coating is of a compressive stress and the base metal is of a tensive stress. 计算结果表明,由于瓷层与金属基体热膨胀系数存在差异,瓷层处于压应力状态,金属基体处于拉应力状态;
- As the radium of pipe increases, the absolute value of the radial stress decreases, and the compressive stress o... 随着管道半径的增大,径向应力绝对值减小,瓷层所受的压应力也减小。
- Earlier stage was NS compressive stress and thereafter EW compressive stress,later stage NS torsion stress. 先期为南北向的挤压应力,其后是东西向的挤压应力作用,后期为南北向的扭动应力作用。
- An applied tensile or compressive stress resolved into a shear component along a specific plane and direction within that plane. 一个实际拉或压应力沿某一特定平面和在该平面特定方向上分解得到的切应力分量。
- Objective To investigate the effect of different diameter powder on setting time and compressive stress of carbonated hydroxyapatite cement (CHC). 目的 检测不同粉体粒径对碳酸化羟基磷灰石水泥 (carbonatedhydroxyapatitecement,CHC)的固化时间和压缩强度的影响 ,为其修复骨缺损提供理论基础。
- The results show that the orientations of principal compressive stress and principal tensile stress are NEE and NNW respectively. 结果表明：主压应力为北东东向，主张应力为北北西向；
- The maximum draw stress located on the lingual apex, while the maximum compressive stress located on the lingual crest of the ridge. 最大拉应力位于舌侧根尖部，最大压应力位于舌侧牙槽嵴顶。
- The growth behavior of short through-thickness crack in the residual compressive stress which was introduced by a pressin method was investigated. 摘要用压入法引入残余压应力，以研究穿透短裂纹在残余压应力中的扩展规律。
- The shift of G peak position toward lower wavenumber is because of the releasing of compressive stress in a-C:Cu films by the addition of Cu. 实验结果显示随著铜含量增加，发现粗糙度提高并且表面尖锥数量增加及细化的现象，但铜在膜中分布均匀。
- Under axial force, moment and shear force steel-concrete joint subjected to compressive stress, tensile stress and shear stress. 在轴力、弯矩和剪力的作用下，钢-混凝土接头处将产生轴向压应力、拉应力和剪应力。
- When this model is combined with the theory of excluded volume, experimental critical compressibility factor and Boyle value are obtained together. 模型与排斥体积理论的结合从理论上同时给出了氩气的两个实验数据:玻意耳点和临界压缩因子。
- By improving and optimizing some parameters of shot peening technology,we can acquire desired residual compressive stress and its depth below surface. 通过控制喷丸工艺参数，寻求理想的残余压应力值和残余压应力层深度。
- In the plastic limit analysis,the wrinkler's plate is smartly analyzed in yield-line theory to get the critical compression strength of the coal pillar. 在分析过程中,利用机动法对温克尔地基板(弹簧支撑板)进行了塑性极限分析,得出了煤柱抗压强度的临界值。
- The magnetostriction along the growth direction of these samples and the dependence of magnetostriction on compressive stress have been investigated. 研究了沿着这些样品的生长方向的磁致伸缩性能以及磁致伸缩性能与压力之间的关系。
