您要查找的是不是：
- deep drawing step 拉深工步
- The draw step is the third step of the beginning phase. 开始阶段的第三个步骤，就是抽牌步骤。
- Containers, lids and deep drawing injection moldings. 容器、盖子和深拔注塑。
- Dredge lets you replace any card draw, not just the one during your draw step. 发掘让你可以替代任何一次抽牌，而不是仅限抽牌步骤中的那次。
- Deep drawing stcel for auto headtamp fuel tank, car door and windows. 汽车前车灯、油箱、轿车门、窗等深冲压成形加上用钢。
- An analytical model is established for axisymmetric parts in deep drawing. 摘要建立了轴对称件拉深侧壁起皱的数学模型。
- The second time, however, eight slivers from the first finisher- drawing step are subjected to the same operation. 在进行第二次并条时,第一个并条机生产的八根棉条被送到第二个并条机上进行同样的梳理。
- For yarns that require the additional step, the card sliver goes through the breaker- drawing step and then to the combing operation. 对于需要精梳的纱线,梳棉棉条通过头道并条后,进入精梳工序进行加工。
- The second time, however, eight slivers from the first finisher - drawing step are subjected to the same operation. 在进行第二次并条时,第一个并条机生产的八根棉条被送到第二个并条机上进行同样的梳理。
- The deformation of cone-box shaped part in hydromechanical deep drawing is simulated by the FEM software ANSYS. 摘要利用大型有限元分析软件ANSYS对锥盒形件充液拉深的成形过程进行了数值模拟。
- The 3D simulation model of box deep drawing was presented and validated with the homologous experiment. 摘要建立了矩形盒拉深成形的三维仿真分析模型，并将其与实验结果进行了对比验证。
- Abstract: Blank holder structure and blank holder force （BHF） are very important to the part quality in deep drawing. 摘 要: 压边结构及压边力对板料拉深成形质量有着重要影响。
- Kawai N.Critical conditions of wrinkling in deep drawing of sheet metals. JSME. 1961. 梁炳文.;胡世光
- At the beginning of each player's draw step, that player loses 3 life, searches his or her library for a card, puts it into his or her hand, then shuffles his or her library. 在每个牌手的抓牌阶段，该牌手失去3点生命，从其牌库中寻找一张牌，将其放入手牌，然后该牌手洗其牌库。
- The finite-element code ANSYS/LS-DYNA was used to simulate the process of rectangular box deep drawing. 利用有限元软件ANSYS/LS-DYNA研究变压边力对矩形件拉深成形性能的影响。
- They are deeply drawn by God and they adore Him. 常被神的作为深深吸引并爱慕神。
- Deep drawing experiments were carried out for tailor\|welded blank square boxes. 本文对拼焊板方盒件的拉深成形进行了试验研究。
- A new method has been used to simulate the actual blank holding process in deep drawing of a washing trough. 采用新的研究方法模拟水槽拉伸的实际压边过程。
- The finite element model of hydro-mechanical deep drawing is established based on the commercial software DYNAFORM-PC. 采用商用有限元软件DYNAFORM-PC，建立了筒形件液压-机械拉深过程数值模拟模型。
- Your start phase is when you get ready for a new turn. It's divided into two steps: the ready step and the draw step. 开始阶段分两部分:准备好和抽牌。
