您要查找的是不是：
- die fill ratio 体积压实比
- It showed that the filling ratio and the locatio... 充满度越高,所对应的接枝率增长量也就越大。
- This method can realize net shape forging by optimizing preform die shape.Flashless final forging with complete die fill and without folding-over defect can be obtained. 该方法通过优化设计预成形模具形状，可实现精形终锻，得到无飞边、完全充满型腔和无折叠的终锻件。
- Using the datum curves from the twin screw extrusion experiment,the correlative factors influencing the fill ratio of screw are analysed. 利用双螺杆挤出实验中的实验数据曲线，对影响螺杆填充率的诸相关因素进行分析。
- The influences of working fluid, Fill Ratio of liquid and inclination angle on the thermosyphon operating were analyzed. 试验发现工质为水的热虹吸管的启动时间大于工质为酒精的热虹吸管；
- Lower aerosol velocity provides an active effect on capturing fine particles and higher fill ratio of ferromagnet media has an active effect on capturing big particles. 较低的气体流速有利于小颗粒的捕集，而较高的磁介质填充率对于大颗粒的捕集更为有利于。
- The particle capture efficiency rises with the increase of particle magnetization, magnetic field gradient and fill ratio of ferromagnet media, and it reduces with the increase in aerosol velocity. 磁场强度和磁介质填充率的增加可以提高颗粒的捕集效率，而气体流速的增大则会导致颗粒捕集效率降低。
- The method of applying local loading to die forging was introduced in this paper. And a program for calculating the die filling efficiency was developed. 本文介绍了在模锻工艺中实现局部加载的方法，编制了计算局部加载时模腔充填效率的电算程序。
- After the screw geometrical frame and the assorted form of screw elements are chosen,there are different biggest screw fill ratios under different opertional conditions. 在螺杆几何结构及螺杆元件组合形式确定之后，不同的操作工况条件下对应有不同的螺杆最大允许填充率。
- Based on these work,the effect of the current,the filling ratio and the shape of electrode end on the distrib... 并以此为基础,研究了熔铸电流、填充比和电极端部形状对熔渣流速分布的影响,为实际生产提供了依据。
- The simulating results show the relations of filling ratio with time, filling mass rate with time and the ullage pressure with time. 计算域包括储槽内部，加注管路和侧满管路，通过程序仿真得到加注过程中加注流量、储罐内液体的充满率、储罐内的压力随加注时间的变化规律。
- It took me quite a while to fill out the questionnaire. 填写那份问卷花了我好长一段时间。
- These preventing measures include the control of the operating temperature, the filling ratio and speed control, spilling and leakage control etc. 其中包括操作温度的控制，投料配比和速度的控制，以及溢料和泄漏的控制。
- Fill your radiator with water, or your engine will overheat. 给你的散热器充水，否则引擎会过热。
- The results show that the greater casting thickness, rotating speed and radius of centrifugal casting are, the greater the filling ratio are. 试验结果表明,试样铸件厚度越大,离心半径越大,离心转速越高,铸件型壳的充填率越高。
- Don't let defeat fill you with gloom. 别让失败使你灰心丧气。
- Every winter some old people die from hypothermia. 每年冬天都有些老人死于体温过低。
- The BBC often plays a record to fill in. 英国广播公司经常在节目空档时播放唱片。
- Can you fill in for Steve tonight as he's ill? 史蒂夫病了，今晚你能顶替他吗？
- Can you fill me in on what has been happening? 你能把发生的事情原原本本地告诉我吗？
