您要查找的是不是：
- dry contact pressure 干接触压力
- Contact pressure increase by 1.5 - 5 with same stems and yokes. 即使采用相同的阀杆和轭架;接触压力也能够增加1.;5至5倍。
- However, the current theory for fatigue strength design is based on Hertz theory which is only applicable to dry contact of smooth surfaces. 然而,现行的齿轮传动接触疲劳强度设计基于仅适用于光滑表面干接触的Hertz理论。
- The perfect camber design can be obtained by introducing the center/side ratio concept of contact pressure and choosing proper ratio. 同时引入辊间接触压力的中、边部比值概念并作合理选择，使设计出的辊型更加完善。
- The relay module has eight isolated relays that can be used to switch power or provide a dry contact as an enable signal. 继电器模块带有四个独立的继电器，用于转换电源或者提供一个干式接点作为可用信号。
- The high contact pressure and the choice of different electrical contact materials enable high currents to be switched reliably. 高接点压力和选择不同的电接点材料能可靠地控制大电流。
- Then press LongDe dry contact LiuTao boss about netizen leaks, LiuTao smiled and said: "this person is so I can not screenwriter, high IQ devised such things to hype. 随后记者致电中乾龙德老板刘韬，谈及网友的爆料，刘韬笑着说：“这个人是编剧，我可没有那么高的智商想出这样的事情来炒作。
- The difference between the PFL and FFL is not obvious for large tensile stresses and so does the effect of the contact pressure on the FFL. 当拉应力较大时，微动疲劳寿命（FFL）与普通疲劳寿命（PFL）相差不大，法向压力的影响不明显；
- Sufficient contact pressure generated by the torque is essential. A small increase in contact pressure produces a rapid decrease in leakage. 通过扭矩产生充足的接触压力是重要的。接触压力的稍微增加，可以迅速减少泄漏。
- In this paper, the residual contact pressure of hydraulically expanded joints of tube to single tube model of heat exchangers is investigated. 采用液压胀接技术，对换热器液压胀接后管子与单管模型的残余接触压力进行了研究。
- The application results show that the distribution of roll contact pressure was meliorated, and the life of the backup roll was improved. 结果表明，优化后的辊型曲线改善了辊间压力的分布情况，降低了轧制末期工作辊边部对支撑辊的磨损，提高了支撑辊轧制质量。
- More detailed thermographic testing on an annual basis is required to ensure that contact pressure does not deteriorate over time. 更详细的温度测试，每年需要，以确保接触压力并不恶化一段时间。
- It can be concluded that the diameter of the tubesheet has little influence on the contact pressure and the residual contact pressure. 得出液压胀接时管板外径对胀管的接触压力和残余接触压力影响不大等结论。
- Peak value alarm 1 and 2 have each a separate dry contact output that is activated (or deactivated, still depending on the ALARM CONFIGURATION MENU) when the alarmthresholds are reached. 当报警端到达的时候，有单独的系统状态报警干式接点输出的峰值报警1和2被激活（或取消，依靠报警配置菜单的设定）。
- Hence, an increasing of CoF could reduce the slip distance and increase the friction stress but does not ensure a decreasing in peak contact pressure. 因此，摩擦系数增加，能减少滑动距离和增加摩擦应力，但不能确定最大接触压力的减少。
- The calculating formulas related the residual contact pressures to hydroform... 结果表明该装置结构及其计算方法适于工程应用。
- The inexpensive tried and tested Bourdon tube system coupled with a modern modular principle provides a very reliable yet inexpensive contact pressure gauge. 经过测试和使用的波登管系统价格便宜,采用现代化的模块原理,是一个可靠的价格合理的接点压力表。
- At high pressure dry ice will melt. 高压下干冰会溶化。
- The different expansion joint set in lining-up BOF will lead the different of contact pressure between lining and shell,and further produce different thermal-stress. 转炉炉衬砌筑时设置的膨胀间隙不同会导致炉衬与炉壳之间的接触压力不同,进而导致炉衬的热应力不同。
- The FEM analyses indicate that maximum contact pressure and maximum friction energy intensity caused by ultrasound also occurs always at the periphery of conta. 有限元模拟的结果显示,最大的接触压力以及由此导致的最大摩擦能密度也发生在接触界面的周边,从而解释了实验现象。
