您要查找的是不是:
- equation of vane profile 叶片型线方程
- The equation of wealth with happiness can be dangerous. 把财富与幸福等同起来是很危险的
- Criteria for using an equation of state. 使用状态方程的标准。
- An algebraic equation of the fourth degree. 四次方程式
- The stators inner suface of vane pump is very complicated.When machining the su rface,special profile grinding machine. 叶片泵定子曲面的形状比较复杂,修磨时往往需要专用仿形磨床。
- The application of process of vane wheel profile forming can ensure the machining accuracy and improve the productive efficiency. 采用成形铣削加工叶轮型面,保证了加工精度,提高了生产效率。
- If we drop one variable, we must also drop one equation of motion. 如果我们去掉一个变量,则必须同时去掉一个运动方程。
- Kinetic parameters were obtained using the equation of Kissinger. 利用Kissinger方程给出了其动力学参数。
- Kinematics equation of six-wheel Lunar Rover are presented. 首先推导出六轮月球车运动学方程 ;
- The regressive equation of skew ratio is built by tests. 通过实验建立了平辊轧制矩形件及轧件脱方的回归模型。
- Equal equations of equator quiver equivalently. 相等的赤道方程式均等颤动。
- Based on the general equation of curved profile worms, the reverse solution principle of parameters of these worms is introduced. 基于曲纹面圆柱蜗杆的一般方程 ;探讨了该类蜗杆齿廓参数反求原理 .
- The function and limitation in milling module of UG about milling the bottom of vane was analyzed. 然后介绍了UG软件的铣加工模块中关于叶片清根的功能及局限性;
- Based on the tooth profile curve equation of inner rotors in cycloidal pump, the formula for displacement calculation of the pump are derived. 根据摆线泵内转子的齿廓曲线方程,推导出了摆线泵的排量计算公式。
- There is a vane on top of the building. 在大楼的顶端有一只风信旗。
- The paper analyzes the lose efficacy form,wear and tear mechanism of vane wheel. 分析了叶轮的失效形式及磨损机理,设计出一种新型高铬锰铸铁耐磨叶轮。
- In this paper, a new concept of the reference cylinder of ZK worm is presented on the basis of the established equation of profile of ZK worm. 在推导了曲纹面蜗杆齿面方程的基础上,提出了曲纹面蜗杆拟准圆柱的新概念,研究了拟准圆柱的横截面半径随加工工艺参数的变化规律,并且通过实验得到了验证。
- The problems about milling the bottom of vane were resolved by adjusting parameters. 最终通过参数调整的方法解决了叶片清根中存在的问题。
- Meanwhile obtained the tooth profile equation of pin-track by the tooth profile normal law which matched the inviolate-cycloid compound gear. 同时利用齿廓法线法得出与该复合齿轮相配套的销轨齿廓方程。
- The section curve equation of main stirring shaft is obtained by deducting the screw profile curve formation process of the stirring kneader. 摘要用数学方法对搅拌捏合机搅拌轴螺杆外形曲线的形成过程进行了详细的推导,得出了主搅拌轴截面曲线形状公式。