您要查找的是不是：
- faulty signaling link 故障信号链路
- Signaling Link Code = the member number within a link set. Signaling Link Code = 链路群内的成员号。
- Signaling Link Code--he member number within a link set. Signaling Link Code -- 链路群内的成员号。
- The CHG:SLK command is used to change the minor state of a signaling link. CHG:SLK 命令用于更改信令链路的次级状态。
- Major State of Link = the major equipage status of the signaling link. Major State of Link = 该信令链路的主要设备状态。
- For example, an input sensor may be feeding an accurate analog reading to a signal converter, but a faulty signal converter may be sending the CPU an inappropriate digital signal. 例如，输入传感器向信号转换器输入一个正确的模拟信号，但是错误的信号转换可能向CPU输入错误的数字信号。
- The device routes or switches incoming messages to an outgoing signaling link using routing information within the multitiered SS7 message. 该装置为利用多层七号信令报文中的路由信息，为进来的报文送到输出的信令链路上建立路由或进行交换。
- This state Indicates that the AP-DS1 is available for use by an RCS signaling link. 该状态表明 AP-DS1 可供 RCS 信令链路使用。
- Link Node Address (Group and Member) = the node within the IMS ring on which the signaling link terminates. 链路节点地址 (Group and Member) = IMS 环路内信令链路终止的节点。
- Signal unit initial alignment - invokes initial alignment prior to activating or restoring a signaling link. 信令单元初始定位 -- 在激活或恢复信令链路之前调用初始定位。
- Signaling links are usually equipped in pairs in SS7 networks. 信令链路常常是成对地装配在 SS7 网络中。
- Possible reasons: lack of memory, high processor load, faulty signals or timeouts between SW subsystems, faulty messages from BSC. (see TR AE55267). 可能的原因是内存不够、处理器负荷太大、各个软件子系统中出现错误信息或者通信超时。
- The s7ln form (SS7 link) is used to define the individual SS7 signaling links. s7ln 表(SS7 链路)是用于定义各 SS7 信令链路。
- Based on the faulty signals collected from our rotor test rig, the grey correlation analysis was studied for vibration fault diagnose of steam turbine shaft system. 摘要以汽轮机轴系典型振动故障模拟试验为基础，利用灰关联分析理论对汽轮机轴系振动故障的识别进行了研究。
- Far-End CLLI = the Common Language Location Identifier (CLLI) that is associated with the STP or 5ESS DCS at the far end of this signaling link. Far-End CLLI = 与该信令链路远端处的 STP 或 5ESS DCS 相关的公用语言位置标识符 (CLLI)。
- Each signaling link may accommodate a traffic load of approximately 40 percent of its maximum load capacity. 每一信令链路可容纳其接近最大负载能力 40%25 的话务量。
- Major State of Link-this field contains the major equipage status of the signaling link. Major State of Link -- 该信令链路的主要设备状态。
- an accident caused by a faulty signal 错误信号造成的事故
- Far-End Point Code = the point code of the SS7 application at the far end of this signaling link. Far-End Point code = 该信令链路远端 SS7 应用程序的点编码。
- SS7 access link. A dedicated SS7 signaling link not physically associated with any particular link carrying traffic. SS7（7号信令）访问链路。SS7专用信令链路物理上不与任何特殊链路传输业务相关联。
