您要查找的是不是：
- Had machined " soft, sodden " food, often can add speed to feed speed. 加工过“软、烂”的食物，往往会加快进食速度。
- The simulated results show that the fishtail shape coefficient is high when the feed velocity is relatively low and will be reduced with increase of feed velocity. 结果表明：进给速度相对较小时，环件鱼尾形状系数较大，随着进给速度进一步增大，鱼尾形状系数反而减小。
- Feed speed of leather can be adjusted according to the request of technology of leather. 送料速度无级调速,可根据不同皮料需要调整适合的工作速度;
- The rotate speed of shoe tree and feed speed of vibration roller can be adjustedaccording to the leveling requirement. 鞋楦的旋转速度和震荡滚轮的前进速度,可配合平整之需求来加以调整。
- The thrust is greatly affected by the feed speed while the torque is obviously affected by drill geometries. 进给速度对轴向力的影响较大;而钻头几何形状对扭矩的影响较大.
- With PLC controlling feed speed automatically, this machine, occupying little space and enjoying configuration, is easily operated. 本机床结构紧凑,占地面积小,PLC自动控制进给速度,操作简便。
- The results show that the effects on surface roughness are feed speed, depth of cutting , tool rake angle and parts hardness in turn. 结果表明:工件进给速度对表面粗糙度的影响最大,切削深度和刀具前角次之,工件硬度影响最小。
- The simulation system considers the acceleration/deceleration control of feed speed therefore the simulation time equals the real process time. 同时由于该仿真系统考虑了进给速度的加减速控制,因而此仿真时间与实际加工时间相符。
- The quality of the workpiece surface is subject to the matching relation between the feed speed and the sawing speed to some large extent. 框锯机锯切工件表面加工质量在很大程度上取决于进给速度和锯切速度的匹配关系。
- Stepless adjust of wire feed speed and welding, cirumferential welding, filler welding, butt welding, lap welding and fillet welding in flat position. 送丝速度和焊接速度可无级调节，保证焊接稳定；可直焊、环焊、角焊、对焊、搭接焊、及船状位置和角焊接。
- Itanalyzes systemically the influence of wire feed speed, melting rate andthe variations of droplet on arc length, and founds its mathematical model. 系统地分析了送丝速度、熔化率、熔滴的变化对弧长的影响,并建立了其数学模型。
- Vibrating direction angle and motor speed has great impact on the vibrating system and stuff feed speed of grain clearing equipment. 振动方向角和电机转速对粮食清理设备的振动体制和物料推进速度有很大影响。
- The feed speed of programming must be cor rected for realizing high-efficiency machining, and the calculation method of sp eed was given. 为了实现高效率加工,需要对编程进给速度进行必要的修正,并给出了速度修正的计算方法。
- Furthermore, the way how to extend the function served to readjust adaptively the feed speed is studied on the basis of system restructuring mechanism of FSM. 基于FSM的系统重构机理，研究了在系统中扩充自适应调节进给速度功能的方法。
- Whenever a knop is to be formed,the feed speed of decorative yarn with increase,so that certain length of yarn that is enough to form the knop can be supplied. 该方法是保持芯纱的运动速度恒定不变，让饰纱按要求改变运动速度，在需要形成结子时提高饰纱的喂入速度，以满足形成结子所需的用纱量。
- Switchover from rapid to feed speed is position-dependent and is initiated by the limit switch S2, which feeds an electrical signal via the relay K2 to the solenoid coil Y2. 从急流向加料速度转换是要看情况的,并且转换被通过继电器K2向磁铁线圈Y2汇聚电信号的限位开关S2初始化。
- Research on Feed Velocity Control Model of Axisymmetric Aspheric 轴对称非球面加工进给速度控制技术研究
- The testing way of reversal value was introduced,and the complement method was presented based on the character that reversal value varys with feed speed. 介绍了反向偏差的测定方法及其随进给速度变化而变化的特点,并基于该特点给出了相应的补偿方法。
- Effect of Feed Velocity of Mandrel on Cold Ring Roll Process 芯辊进给速度对环件冷轧工艺的影响规律
- The experiment results showed that when feed speed was increased, width-radius ratio can reduce the width spread ratio and flat the side surfaces of ring in some extend. 通过对实验结果的分析表明：进给速度和宽径比的增加都可以在一定程度上减小环件的宽展，使环件端面平整。
