您要查找的是不是：
- The contribution of the guide surface roughness overshadows that of the fiber surface roughness. 导纱杆表面粗糙度的作用超过纤维表面的粗糙度。
- There also exists much fiber surface damage brought about by beaters, card clothing, faller pins, etc. 打手、钢丝布和梳针等金属机件都会损伤纤维表面。
- The following remarks refer to the effects of mechanical processing on fiber surface geometry. 下面介绍机械加工对纤维表面几何形状的影响。
- However, there exists also much fiber surface damage brought about by beaters, card clothing, faller pins, etc. 此外，打手，钢丝布和梳针等金属机件都会损伤纤维。
- Friction increases with increasing fiber surface roughness in the boundary and semiboundary. 在边界和半边界区内，摩擦随纤维表面粗糙度的增加而增加。
- ESEM images indicated that fibrils were present on the fiber surface after synergistic treatment. 纤维素酶、半纤维素酶与漆酶/介体处理后，纤维表面出现细小纤维。
- Both IR analysis and TG analysis shows that carbon fiber surface has been grafted by isocyanic ester and caprolactam. 红外和热重分析都表明，碳纤维表面已接枝上异氰酸酯和己内酰胺。
- The contribution of the guide surface roughne overshadows that of the fiber surface roughne . 导纱杆表面粗糙度的作用超过纤维表面的粗糙度。
- Vf , fiber orientation, fiber surface treatment, load and velocity have an great effect on friction and wear properties of K3D/EP composites. Vf、纤维取向、纤维表面处理以及载荷和速度对K3D/EP复合材料的摩擦磨损性能有很大影响。
- The working principle of the optic fiber surface plasmon wave (SPW) sensor is based on the resonance of the surface plasmon. 摘要光纤SPW感测器通过表面等离子体波共振来工作。
- Abstract: Rabbit hair fiber is characterized by smooth fiber surface, low coefficient of friction, and the tendency to depilating. 摘 要: 为了克服兔毛纤维表面光滑、摩擦因数小及其产品容易脱毛的缺点，对兔毛纤维用双氧水（30%25）处理后，再配合酶处理工艺，使纤维得到一定的减量率。
- A quasi-distributed optical fiber surface plasmon resonance(SPR) sensor based on wavelength division multiplexing is studied. 研究了一种基于波分复用原理的准分布式光纤表面等离子体波传感器。
- During the sizing treatment, the influence of carben fiber surface and matrix property on the inter facial shear strength are also described. 同时也总结了上浆处理中碳纤维表面性质及树脂基体性能对复合材料层间剪切强度的影响。
- The micro-morphology of fiber surface was analyzed by SEM, and the active functional group on the fiber's surface was analyzed by XPS. 利用扫描电镜和电子能谱，进行了纤维表面形貌分析及表面活性官能团分析.
- It has been found that the pyrolytic carbon matrix does not merely bond mechanically with carbon fiber surface,and the interface is not a simple plane yet. 实验发现，由化学气相渗透工艺所获得的热解碳并非仅与碳纤表面进行单一的机械粘合，也不是一个简单平面。
- AntiReflection coating. A thin, dielectric or metallic film applied to an optical fiber surface to reduce its reflection and thereby increase its transmitting ability. 抗反光涂层。一种薄的绝缘体或金属薄膜（或者是类似薄膜），贴在光纤表面以减少反射，并以此而提高光纤的发射能力。
- Moreover,the increase of S/C ratios suggested that there was a higher lignin sulfonation degree on the fiber surface,Which is a main reason led to higher paper strength. S/C的提高则表明爆破使纤维表面的木素磺化度提高,这是引起爆破浆强度高的原因之一。
- Variations in surface roughness of both guide and fiber surfaces have a marked effect on friction. 导纱器和纤维表面粗糙度的变动，对摩擦力都有显著影响。
- It has shown that on untreated fiber surfaces, the high modulus fiber has much less functional groups than the low modulus fiber. 研究表明，高模量碳纤维的表面化学基团含量要比低模量碳纤维的低。
- The gas bubbled to the surface of the water. 气体变成气泡升上水面。
