您要查找的是不是：
- fiber bonding strength 纤维结合强度
- Bond strength is an important parameter for wafer bond. 键合强度是关系到键合好坏的一个重要参数。
- The bonding strength and the dissipated energy performances of B (staple shape) steel fiber are better than those of the J (shear straight line shape) steel fiber. 型（书钉型）钢纤维的粘结性能和拔出时所耗能量均优于J型（剪切平直型）钢纤维；
- The bonding strength of vapor deposited hard films are measured by this meth... 但人们在膜基结合的测试技术上仍有困难。
- The bond strength experiment of dogtooth exposed to pulsed Nd: YAG laser[J]. 引用该论文 朱建中;黄炜;许肖杰;林斌;陈钰清;顾锡荣.
- Xeno III Adhesive provides bond strength comparable to total etch systems. 异种三胶粘剂粘结强度可比提供总额蚀刻系统。
- The usual method of strengthening concrete structures with fiber reinforced plastic (FRP) is to bond FRP sheets on the surface of concrete, so the bond strength between concrete and FRP sheets is a key issue which affects strengthening. 纤维增强塑料(简称FRP)加固混凝土结构通常是将其粘贴在混凝土的表面;因此FRP材料与混凝土结构之间的粘结性能成为影响加固效果的关键因素.
- Indirect methods to measure the interface bond strength include the interlaminar shear strength test. 测量界面粘结强度的间接方法包括层间剪切强度试验。
- Glue Hard brittle brownish solid made by boiling hides and bones.Dissolves in hot water with good bonding strength. 通过煮沸处理动物皮和骨骼而获得的硬而脆的褐色固体。它溶于热水并具有良好的粘合性能。
- The ARB technique not only increased greatly the bonding strength of TA1/Q235 clad plate,but also thinned the microstructure of Q235 plate. 结果表明采用累积叠轧焊方法不仅可以大幅度地提高TA1/Q235的结合强度,而且还可以获得连续均匀、组织细化的Q235的结合组织。
- There were no statistical differences between the shear bond strengths of carbon fiber post (2.4MPa) and cast Ni-Cr alloy post (3.8MPa). 剪切粘结强度 (MPa) :碳纤维桩 (2 4 )、镍铬合金桩 (3 8) ,IPS Empress 2全瓷桩未与水门汀分离前断裂。
- Glue: Hard brittle brownish solid made by boiling hides and bones.Dissolves in hot water with good bonding strength. 动物胶:通过煮沸处理动物皮和骨骼而获得的硬而脆的褐色固体。它溶于热水并具有良好的粘合性能。
- Finally, the bond strength of FRP bars to epoxy resin and cement grout is also studied. 同时对纤维塑料筋与水泥装和环氧树脂的粘结强度也进行了探讨。
- This paper analysed the influence of specimen thickness on test results of surface bonding strength of thin MDF. 分析比较薄型中密度纤维板试件在检测时组合厚度的改变对其表面结合强度测试结果的影响。
- The conclusion which the bonding strength is obviously influenced by the interlaced yarns. 得出空气变形丝对涂层织物的剥离强度具有显著影响的结论。
- Fiber bonding is achieved either through the use of a binder or adhesive, or by the inclusion in the blend of heat sensitive fibers, which help seal the final fabric as a result of their ability to soften and fuse with other fibers. 纤维的粘合可以使用粘合剂或粘着剂,也可以在纤维中混入热敏性纤维,这些纤维可以软化并与其它纤维粘合,使织物结构稳定。
- Iong open time, high bonding strength。 Dissociative form aldehyde content can meet national standard. 开放时间长，强度好。游离甲醛含量通过国家标准。
- The influences of ultrasonic power on heavy aluminum wire wedge bonding strength were investigated. 超声功率是影响粗铝丝引线键合强度的最主要因素之一。
- A new method for measuring bonding strength between electroplated layer and substrate of diamond tool is proposed. 摘要提出一种新的电镀金刚石工具镀层与基体结合强度测试方法。
- Objective: To study the influence of dry or wet dentin bonding surface on wet bonding strength. 目的:研究牙本质表面的干燥或润湿状态对牙本质湿粘结强度的影响。
