您要查找的是不是：
- gear output shaft 齿轮输出轴
- Standard version: output shaft with keyway. 标准产品:输出轴带键槽.;消声器可拆除
- LF200 consists of a 3-shaft helical gear set and a lockable planetary differential gear. its output shaft and input shaft swivel in the same direction. LF200型分动器由三轴式斜齿轮组和带有可锁式轴间行星式差速器组成，其输出轴和输入轴旋向相同。
- During reassembly, grease the bore of the drive shaft receiving the reduction gear’s output shaft before reinstallation of the clamp ring. 在重组，油脂的膛的传动轴收到减速器的输出轴之前重新安装钳环。
- The low speed shaft features a “no-leak” drywell design that physically separates the oil sump from the output shaft to eliminate gear oil contamination of the tank product. 低速轴的特点是：“无泄漏”的干井式设计，油箱与主轴分离，消除了齿轮油污染槽体内介质的机会。
- Remove the bezel and rubber gasket from the motor output shaft. 从马达输出轴上拆卸玻璃框和橡皮垫圈。
- Dynamic Torque : the degree, the role of the output shaft torque. 动态扭矩：在分度期间，作用在出力轴上的最大扭矩。
- The low speed shaft features a "no-leak" drywell design that physically separates the oil sump from the output shaft to eliminate gear oil contamination of the tank product. 低速轴的特点是：“无泄漏”的干井式设计，油箱与主轴分离，消除了齿轮油污染槽体内介质的机会。
- Newly developed three ring gear reducer is comprised of synchronous belt, big and small pulleys, crankshaft, drive ring plate, output shaft, external gear and case. 设计的新型三环减速器主要由圆弧齿同步齿形带、小带轮、大带轮、曲柄轴、传动环板、输出轴、外齿轮和箱体等组成。
- Stop action : Each output shaft rotation - down a few. 停动数：出力轴每一旋转的停动数。
- The PDT is a gear reducer having multiple output shafts, all driven from a common input shaft. 该泵驱动变速器是一个齿轮减速箱，具有多个输出轴，全部由同一个输入轴驱动。
- Turn the wiper module over and remove the nut that secures the wiper motor crank arm to the wiper motor output shaft. 转动雨刷模组盖，并拆下将雨刷马达曲柄臂固定于雨刷马达输出轴上的螺帽。
- Using a strap pipe wrench, turn stud Item 11 while keeping the drive shaft stationary in order to release the shafting Item 20/11 from the reduction gear’s output shaft. 使用带管扳手，反过来螺柱项目11 ，同时保持平稳的传动轴，以便释放轴系项目20/11从减速机的输出轴。
- Output shaft when the swing set in the center of rotation on the trip-down, design may also need to set rotation angles and movements itinerary. 出力轴在摆动时可设定在旋转行程的中心点上停动，也可依设计需要设定旋转角度和升降行程。
- Stop: stop rotating output shaft, cam rollers contact roller cam bearings taper ribbed support of the re-direct. 停止：出力轴停止旋转，凸轮滚子接触滚子轴承式凸轮锥度支撑肋的重直部分。
- The clutch rotor is fixed on the input shaft and the clutch armature is fixed on the output shaft. 离合器的转子固定在入力轴，而离合器的电极板与刹车被固定在出力轴上。
- Direct drive to the rolls with heavy-duty helical bevel gears where the output shaft is directly coupled to the roll shaft. 高坚固的螺旋斜线轴承直接驱动辊筒。输出轴直接连接辊轴，中间没有任何传动消耗。
- Output flange is connected with output shaft by a involute spline, and fastened by a locknut. 输出突缘通过渐开线花键与输出轴相连，并用锁紧螺母将其锁住。
- The output shaft rotary tables can be used automatically rotating machinery Center momentum. 出力轴上的旋转台可用作自动旋转机器的中心传动力。
- Taper support rib usually two or three cam roller contacts, in order to edge into the axis of rotation to be sent to the uniform output shaft. 锥度支撑肋通常与两个或三个凸轮滚子接触，以便入力轴的旋转可均匀地传送到出力轴。
