您要查找的是不是:
- glass tube forming method 玻璃管成型法
- A glass tube for enclosing the flame of a lamp. 玻璃灯罩围住灯的火焰的玻璃管
- Heat the glass tube to the point that it can bend. 将玻璃管加热,以能弯曲为度。
- Method:Forward and reverse blood types were detected by POSEIDON digital blood typing instrument ,U-type microplate and glass tube method and compared. 方法:使用POSEI-DON数字血型仪、U型板法和试管法进行血型正反血型判定比较。
- Then we made the compound form method to find the optimums. 所编计算程序可通用。
- Seal up one end of a glass tube about 34 inches long. 把长约34英吋的玻璃管的一端封闭起来。
- It consists of a vertical, tapered glass tube containing a movable weight. 它在垂直的锥形的玻璃管内装一个可以活动的重物。
- Adopting the method stipulated by GB18098-2000 Standard,the content of poisonous gas had been determined after single compound was detonated which was bottled with glass tube. 用GB18098-2000标准规定的方法,采用玻璃管装药,测定了单质炸药梯恩梯爆炸后有毒气体的含量。
- This light consists of a glass tube containing argon and a droplet of mercury. 这种灯是由一根充有氩气和微量汞的玻璃管组成。
- A mercurial barometer has a glass tube a little more than 30 inches long. 水银气压表有一长30英寸多一点的玻璃管。
- SOD were tested with nitrite forming method, LPO were tested with thio-barbitone display method. 亚硝酸盐形成法测定SOD,硫代巴比妥显色法测定LPO。
- Quarts glass tubes provided by GE. 灯管采用GE公司石英玻管。
- The gap between the tube blank top tray and intermediate bed slider face influences the tube forming quality greatly. 管坯顶盘与中间床身滑轨工作面之间的间隙很大程度上影响着待轧钢管的成型质量。
- The glass tube ends in a bulb. 玻璃管的末端呈球形。
- Being a precision forming method,Brazing is wildly used in joining complex shape parts and thin wall accessories. 钎焊作为一种精密成型的焊接方法,在形状复杂和薄壁零件连接中获得广泛应用。
- Being a precision forming method, Brazing is wildly used in joining complex shape parts and thin wall accessories. 钎焊作为一种精密成型的焊接方法,在形状复杂和薄壁零件连接中获得广泛应用。
- A mercurial barometer has a glass tube a little more than30 inches long. 水银气压表有一长30英寸多一点的玻璃管。
- Unique design to prevent glass tube from being impacted directly by particles. 独特设计,可防止微粒直接撞击玻璃管。
- Through the comparison of numerical simulation value and experiment results, the range of reduction ratio was obtained while the tube forming ideality. 通过数值模拟与实验结果的比较,得出了获得较理想的成形薄壁筒形件时减薄率的选取范围。
- MPPF is the most optimal forming method, but it is expensive to achieve.More steps of MPDF can approximatively achieve the forming effect of MPPF. 多点压机成形是理想化的成形方式,但设备造价昂贵,多道次多点模具成形可以近似实现多点压机成形效果。