您要查找的是不是：
- governor tie rod assembly 调速器拉杆总成
- governor tie rod 调速器拉杆
- governor tie rod fork 调速器拉杆叉
- governor tie rod fork pin 调速器拉杆叉销
- governor tie rod fork shaft 调速器拉杆叉轴
- This can be done through adjusting the length of the tie rod. 调节前束可以通过调节横拉杆的长度来进行。
- The entire assembly is held to a fixed overall vertical length by tie rods. 整个组件的整体垂直长度由拉杆的位置确定。
- The reconditioned piston and rod assembly is lubricated protected against damage and foreign matter and lapelled to ensure identification. 翻新的活塞与连杆总体已经润滑以防止损坏或异常情况发生。
- The dual elevator system of claim 6, wherein no stabilizing linkage is attached between said input push rod assembly and said vertical stabilizer. 双电梯系统的索赔6 ，其中没有稳定的联系是说，重视投入与推杆集会，并表示垂直稳定。
- Meanwhile, incorrect tie rod adjustment will lead to settlement, malposition or even collapse of crown. 不正确的拉条张力调整也将导致碹顶塌陷、下沉或错位，威胁其安全。
- The tie rod at each end of the rack connects to the steering arm on the spindle. 齿条一端连着拉杆，拉杆与车轮轴上的转向摇臂相连接。
- The method of claim 23, wherein said input push rod assembly comprises a push rod deflection mechanism configured to laterally deflect said input push rod assembly. 该方法的索赔23 ，其中说，投入推杆装配包括推杆偏转机制配置为横向转移说，投入推杆组装。
- Fracture analysis of intermediate tie rod was carried out by metallography, scanning electron microscope and EDS. 采用金相显微镜、扫描电镜、电子能谱仪等方法对钻井泵中间拉杆破断失效进行了分析。
- The method of claim 14, wherein said input push rod assembly comprises a push rod deflection mechanism configured to laterally deflect said input push rod assembly. 该方法的索赔14 ，其中说，投入推杆装配包括推杆偏转机制配置为横向转移说，投入推杆组装。
- Nosecone, Ejection Cylinder and Piston / Rod Assemblies...nosecone ，弹射汽缸和活塞/杆集会...
- All gas line support brackets and tie rods will be galvanized type. 气体管路所有的支架都要镀锌防腐。
- Various tie rod assy. drag link assy, center link. L.H/R.H side link and stabilizer link etc. can be used for many truck and car use. 多种结构和型号的横拉杆总成、直拉杆总成、中间拉杆、左右侧拉杆及稳定杆等，可供诸多载重车、乘用车选用。
- It consists of steering wheel, steering shaft, worm, gear sector, pitman arm drag link, steering knuckle arm, king pin, steering arms, tie rod, front axle and steering knuckle. 转向系统包括转向盘、转向轴、蜗杆、扇形齿轮、转向摇臂、直拉杆、转向节臂、主销、转向臂、转向直拉杆、前轴和转向节。
- On single-ended output's gear rack type diverter, a rack's end with changes the steering knuckle tie rod through the inside and outside bracket to be connected. 在单端输出的齿轮齿条式转向器上，齿条的一端通过内外托架与转向横拉杆相连。
- The calculating formulae for the speed and the acceleration of the tie rod and the ringy gear crosshead are induced based on the kinetic model of the transmission mechanism. 该文通过建立行星齿环传动机构的运动学分析模型，导出了其系杆和齿环滑决速度、加速度计算公式。
