该词条未找到_海词词典

您要查找的是不是：

darcy impact pressure tube 达喂力管
In a pitot-tube, a small filament of the fluid is brought to rest in a small-bore tube, the impact pressure being measured against the static pressure of the fluid in an outer tube. 在全压管内，注入的液体流丝停留在一个小内径管内，全压通过外管内液体的静压测得。
In a pitot-tube, a small filament of the fluid is brought to rest in a small-boron carbide nozzle e tube, the impact pressure being measured against the static pressure of the fluid in another tube. 在空速管中，有微量水流被滞留在小口径管中，然后利用另一管道中的静态液压来测量压力的大小。
In a pitot-tube, a small filament of the fluid is brought to rest in a small-bore tube, the impact pressure being measured against the static pressure of the fluid in another tube. 在皮托管中，细小流体流入并停在一根小孔径管子中，测量其相对于另一根管子中流体静压的冲压（/动压）。
Orifices perforate the piston and allow fluid to leak through as the piston moves up and down in the pressure tube. 打有小洞的活塞就会随着活塞的上下运动，使避震器内的液压油通过小孔在压力管内流动。
The paper presents a design of passive heat-switch between pressure tube and calandria tube of Thorium-based Advanced CANDU Reactor(TACR). 提出了一种可应用于钍基先进CANDU型反应堆(TACR:Thorium-based Advanced CANDU Reactor)压力管与排管间的非能动热开关设计方案。
Jet impact pressure is detectable for large radius of near wellbore formation up to 600 mm at tested pump pressure of 20.0MPa. 在试验的泵压20.;0MPa条件下，射流压力作用深度可达600mm以上。
The paper presents a design of passive heat-switch between pressure tube and calandria tube of Thorium-based Advanced Nuclear Energy System. 提出了一种用于钍基先进核能系统压力管与排管之间的非能动热开关设计方案。
Fault impact pressure is a dynamical phenomenon caused by coal mining, with fault abruptly dip offset, and stretch strain energy rapidly release. 断层冲击矿压是由于开采活动引起的断层突然相对错动、弹性应变能迅速释放的动力现象。
The mainly rubber productions: various rubber special type productions, high pressure tube, rubber airproof strip and tube, resinic tube and so on. 橡胶制品主要有：各种橡胶异型件、高压油管、橡胶密封条、管、树脂管等。
The extension cycle occurs as the piston moves toward the top of the pressure tube, compressing the fluid in the chamber above the piston. 当活塞向压力管上部运动时，发生的是伸展循环，活塞会挤压处于液压管上部的液压油。
The impact pressure of swirling jets, produced by water-cushion swirling abrasive jet nozzle, was measured by continuous shooting images of the symbol in the piezometer tubes. 摘要利用测压排摄像自动读数法，测量了水垫式旋转磨料射流喷嘴所产生旋转射流的冲击压强。
It is found that the impact pressure may be maximal when the ratio of initial air volume,under standard atmospheric pressure,to total volume in pipeline reaches a certain value. 试验结果表明,水流冲击截留气团的最大压力与截团在一个大气压下的初始体积占管道总体积的比例多少有关。
The impact pressure on the surface of product and the flowing velocity were calculated by hydromechanics theory, and the calculation process was programmed by language C. 同时，运用流体力学原理，对冷却管路系统进行了理论计算，得到了喷嘴出口处的水流速度以及作用于钢板表面的冲击压力。此外，利用标准C语言对计算过程编制程式。
Relating the momentum flux of particle with the particle impact pressure on objects, a theoretical model of the particle impact pressure in fluidized bed is deve loped. 通过对床中物体表面与碰撞颗粒流之间的动量衡算，将颗粒流动量通量与颗粒的碰撞压力相关联，建立了流化床中颗粒碰撞压力的理论模型。
The impact pressure of swirling jets,produced by water-cushion swirling abrasive jet nozzle,was measured by continuous shooting images of the symbol in the piezometer tubes. 利用测压排摄像自动读数法,测量了水垫式旋转磨料射流喷嘴所产生旋转射流的冲击压强。
The results show that the speed of airway reopening was dependent on various parameters such as reopening pressure，tube inner diameter，and viscosity and initial length of lining liquid. 结果表明，它们受外加压强，管直径，阻塞液粘度以及初始阻塞液长度的影响。
The stilling basin base plate supports large impact pressure in the impacted area . 消能塘底板在射流冲击下,底板块在冲击区受到较大的冲击压力。
The pressurizing tube sealing is to charge gas into the sealing tube by using controllable pressurizing system,so that the sealing tube has expansion deformation. 充压管密封是利用可控制增压系统向密封管内供应气体,使密封管产生膨胀变形来实现密封。
The stilling basin base plate supports large impact pressure in the impacted area. 消能塘底板在射流冲击下，底板块在冲击区受到较大的冲击压力。