您要查找的是不是：
- The mathematical model was verified in experiment with the method of indirect squeeze cast Archimedean spiral proof sample. And the experimental results show that the maximum deviation between the theoretical value and measured value is less than 8%. 采用间接挤压铸造阿基米德螺旋线试样的方法对该数学模型进行了实验验证,实验结果表明:理论计算值与实验测定值之间的最大偏差小于8%25;
- Coding System for the Die in Indirect Squeezing Casting 间接挤压铸造模具编码系统研究
- T.Etter Strength and fracture toughness of interpenetrating graphite/aluminium composites produced by the indirect squeeze casting process[J].Materials science and Engineering,2004,386:62. 摘要在比较几种常用轴颈尺寸修复特点的基础上，根据大型水泵轴轴承位磨损特徵，叙述了采用电刷镀和热喷涂处理技术修复水泵轴的工艺方法。
- Design if Casr Die in Indirect Squeeze Casting 间接挤压铸造模具设计特点及研究
- A Feasibility Study on Production of Cast MMCs by Indirect Squeeze Casting 复合材料间接挤压铸造生产的工艺可行性研究
- Indirect Squeeze Casting Technology for Bearing Holder 轴承保持器间接挤压铸造工艺
- Study on Mechanism of Cold Sandwich in Indirect Squeeze Casting 间接挤压铸件中冷夹层的形成机理研究
- Design of Indirect Squeeze Casting Process for an Aluminum Alloy Support Frame 铝合金支架间接挤压铸造的工艺设计
- Selection principle on the squeezing casting techniques was discussed. 论述了挤压铸造技术方案的选择原则。
- Effect of Processing Parameters on Mechanical Properties and Hot Tearing Tendency of Indirect Squeeze Casting Al-Cu Based Alloy 工艺参数对间接挤压铸造铝铜合金力学性能及热裂倾向的影响
- A new technology of squeezing casting for small piston is developed successfully with old Y41-63 type equipment. 用Y41－63型旧设备，开发挤压小活塞新工艺获得成功。
- Design of squeezing die as well as good quality and low cost of piston with squeezing casting are introduced. 介绍了挤压模的设计以及挤压活塞的优质和低成本。
- indirect squeeze Casting 间接挤压铸造
- The lower specific pressure and delay pressurization in time during casting process were responsible for surface blister and cold shut of motor cycle wheel in squeezing casting. 分析了实际铸造比压偏小以及不能瞬间及时增压是造成摩托车车轮挤压铸件表面起泡和冷隔的主要原因。
- That guy is capable of squeezing money out of his old mother. 那家伙做得出勒索老母亲钱财的事来。
- It is pointed out that the rational squeezing casting technology can refine microstructure and improve the component compactness as well as the mechanical properties of alloy. 指出合理的挤压铸造工艺可细化合金显微组织,提高铸件致密性,改善合金力学性能。
- Effects of heat treatment on microstructure of aluminosilicate short fiber reinforced ZL108 composites prepared by squeezing casting have been observed. 研究了热处理工艺对挤压铸造制备的硅酸铝短纤维增强ZL108合金复合材料组织的影响。
- That volcano cast forth lots of lava and ashes. 那火山喷了出大量熔岩和灰烬。
- The squeezing casting of Zn-Al alloy merges the advantage of casting and forging and has the broad development under the situation of more and more high demand to casting quality. 锌铝合金挤压铸造结合了挤压铸造和锌铝合金的优点,在当今对铸件质量要求越来越高的形势下,具有广阔的发展前景。
- She cast her eyes down to avoid direct eye contact. 她垂下双目以避免对视。
