您要查找的是不是：
- Product initial temperature, describe method used to determine I.T. 罐头的初温要求,记述测初温的方法。
- Initial temperature of catalyst bed is wholly too high. 提高起始反应温度使催化剂床层温度整体过高导致飞温。
- The lower the initial temperature, the slower the start of active fermentation. 最初的温度较低,发酵慢开始活跃。
- In drain experiments, the drain mass increased with PRZ initialpressure and initial temperature of CMT. 在排水实验中，排水量随着PRZ初始压力的升高而增加，随着CMT初始温度的增加而增加。
- However, the pressure response of CMT is mainly affected by the initial temperature of CMT. 实验发现，CMT内温度分布和凝结特性主要受PRZ初始压力和CMT初始温度的影响，而压力响应主要受CMT初始温度影响。
- The main purpose of this software is to provide a correct initial temperature distribut... 该简化算法运算时间短，可以满足实际应用中对运算时间的要求。
- The entanglement achieved by fields heavily depends on their initial temperature and the detuning. 这个通过热场获得的纠缠深深的依赖于初始热场的温度和失谐。
- Ceramic material had better performance than steel and copper and the shorter the stack, the lower the initial temperature for oscillation. 而从热声振动的方式来看，强制振动比自激振动具有更低的起振温度。
- The physical meaning of the initial temperature and the peak temperature determined by DSC extrapolation has been con firmed through variance analysis. 通过对比实验的方差分析探讨了DSC法外推起始温度及峰值温度的物理意义。
- The results indicated that the absorbent cotton and bamboo had a lower initial temperature than polypropylene when pyrolyzed. 与纤维素类的脱脂棉和竹子相比，聚丙烯的分解反应起始温度明显较高。
- Then the key process parameters of laser bonding, including laser power, scanning velocity, and initial temperature, are obtained with the help of scanning experiments. 运用该模型计算了不同的工艺参数条件下硅/玻璃的温度场分布，并由此得出键合线宽。
- Optimizing design of the initial temperature difference(ITD),which is one of the main design parameters in air-cooling systems,plays an important role in raising its economy. 作为空冷系统最主要的设计参数,初始温差值(ITD)的优化设计对提高直接空冷系统的经济性起着举足轻重的作用。
- Quantitatively analyses the concrete influences on atomizing humidifying performance of the nozzle aperture, initial temperature and the pressure of spray water and the water-air ratio through a single factor experiment. 通过单因素试验定量分析了喷嘴孔径、喷水初温、喷水压力以及水气比对雾化加湿的具体影响。
- The effects of polymerization conditions, including initial temperature of polymerization, stirring speed, the type and amount of suspension agent, on the stability of system and water absorbency of resin have been investigated. 研究了聚合初始温度、搅拌转速、分散剂的种类及用量等对聚合稳定性、树脂粒径和吸水性能的影响。
- The simulation results showed that a nanoclusters coalesces with other ones to a greater degree and the temperature changes greater with the decreasing cluster size at constant initial temperature. 结果表明：相同初始温度条件下，随着团簇尺寸的变小，并合程度升高，并合过程中温度上升幅度变大；
- By use of a computer acquisition system, the initial temperature field of ductile iron casting by EPC process was tested and compared with that of the traditional empty cavity process. 用计算机数据采集系统测试了消失模和空腔铸造的初始温度场分布,结果表明,两者初始温度场分布仅有微小差别。
- When two parcels of air with different initial temperatures are mixed, the result is a mixture with a higher relative humidity. 当初始温度不同的二个气块混合时;结果是形成一个具有较高相对湿度的混合物.
- Measures the initial temperature in underground heat exchange wells before heat pump system operating and obtains a fitted equation of initial underground temperature for Changchun area. 测量了地源热泵系统运行前换热井内的初始温度，推导出了适合长春地区的初始地温拟合方程。
- A small adjustment will equalize the temperature in the two rooms. 稍作些调节就会使两间房内的温度相等。
- There is an imperceptible change in temperature. 温度有细微的变化。
