该词条未找到_海词词典

您要查找的是不是：

Injection pressure and holding pressure i. 注射压力和保压压力。
As an example with casing damage in Yushulin oil field of Daqing,the paper calculates the relations between injecting pressure,casing stress and casing strength. 以大庆榆树林油田砂岩段的套损情况为例，计算了注水压力、套管应力及套管强度之间的关系。
Changing feature of cavity pressure with injecting pressure and holding up pres-sure,and the effect in crystallinity and rnechanical properties of PP injecting products,were stud-ied. 研究了注射成型中模腔压力随注射压力、保压压力变化的特征，以及这种变化对聚丙烯（PP）制件结晶度和力学性能所产生的影响。
Injection pressure was 20 pis, 5 sec and power supply was 15kV constant. 自动气压进样;20pis;5sec.
In the mid-anaphase of Injecting Water Development OilField,In order to improving the recovery ratio,Controling Permeability profile of High Layer and Improving injected Pressure will be needed. 对注水开发的油田的中后期,迫切需要控制高吸水层位吸水量,提高注入压力,提高低吸水层的吸水量,达到改善吸水剖面,提高波及体积,以达到提高采收率的目的。
Injection pressure of J-ELIII series is different from that of JSW's hydraulic machines. 注塑压力与油压系列不同。
Maximum injection pressure and maximum holding pressure may be restricted due to molding condition. 有的情形下,最大注塑压力,最大保压压力会因成成形条件不同而受到限制。
Injecting animals is all in a day's work for a vet. 给动物注射是兽医的日常工作。
Colon hydrotherapy equipment can sustain a regulated and safe injection pressure to permit cleaning water to reach th extremities of the colon. 大肠水疗法设备能够维持一个规范和安全注射压力,让水清洗,以达到末端结肠。
Increased needle injection pressure was obsered as the olume of PMMA increases and as the distribution of PMMA is in close proximity to the cortical walls. 同时，使用的聚甲基丙烯酸甲酯黏合剂的体积的增加还可以增大融合椎体的强度。
The pH of buffer was 6.2, and the run-voltage was 7kV. Pressure injection model was used and injection pressure was 2406.25 kPa xs. 运行电压为7kV，采用压力进样方式，进样压力为2406.;25kPa×s。
In the Common Rail accumulator injection system, the generation of the injection pressure is separate from the injection itself. 在共轨蓄压喷射系统，新一代的喷射压力是分开的，从注射本身。
The calculating formula for the plastics backface shrink pitfall value of the strengthening rib was put forward at considering the processing conditions of injection pressur... 提出了在考虑注塑压力、注射温度、注射速率等工艺条件下,塑料件加强肋背面的缩陷值的计算公式,并找出通过模具尺寸设计进行补偿的方法。
They are injecting him with a new drug. 他们正为他注射新药。
The injection pressure and flow rate and the lengths of injection and falloff periods are the key factors to the succession of well test. 注入的压力、排量以及注入和压降段的时间是关系到试井成功与否的关键因素。
Die inserts, together with the cores which form recesses, must endure the effects of temperature and injection pressure of the molten metal. 与形式隐藏，必须忍受温度和熔融金属的射入压力的作用的核心一起死插入物。
Compared with the formation water drive reservoir without water-sensitive damage,the injection pressure of water drive in the water-sensit. 影响木钵区块延10油层驱油效率的主要因素是储集岩的孔隙结构非均质性、水敏伤害、注水压力及加压方式。
Research results show that with application of Mucell,the 10% raw material can be saved,the injection pressure is decreased by 36.7%,the clamp forc... 研究结果表明:采用微孔发泡注射成型工艺可以节省原材料10%25;注射压力降低了36.;7%25;锁模力降低了60
The results showed that Sauter Mean Diameter (SMD) of biodiesel decreased, as the injection pressure increased and the orifice diameter diminished. 结果表明：随着启喷压力的增加和喷孔直径的减小，生物柴油索特平均直径不断减小；
Aiming at the feature of filling tube and injection pressure, non-flowback acidizing was developed to ensure the implementation of miscible flooding. 技术应用将会有一定的借鉴和指导意义。