您要查找的是不是：
- Calculation of the Interference Fit Joints at High Rotary Speed 高速旋转状态下压配合联接的设计计算
- interference fit joint 过盈配合联接
- Study of Stress Concentration and Edge-Effect of Interference Fit Joints 过盈配合接触边缘效应与应力集中
- Bearings with a tapered bore are always mounted with an interference fit. 带圆锥孔轴承始终以过盈配合安装。
- FEM stress analysis of assemble symmetrical body of interference fit. 过盈配合组合轴对称体有限元法应力分析
- Therefore, the ring need not necessarily have an interference fit unless this is required for other reasons. 因此,轴承圈不一定要有过盈配合,除非因其它原因需要这样做。
- For bearings having a tapered bore, inner rings are always mounted with an interference fit. 对于圆锥孔轴承,内圈的安装始终采用过盈配合。
- Alignment needle roller bearings should have an interference fit in the housing bore. 对中滚针轴承的轴承座孔应过盈配合。
- The bearings are generally mounted with an interference fit on the roll necks and therefore often have a tapered bore. 轴承一般以过盈配合安装在轧辊轴颈上,因此经常带锥形孔。
- The material choice, moulding method, joint principle and shape design of hinge joint, hasp joint, clamp joint and press fit joint of normal plastics were introduced. 介绍常用塑料铰链联接、搭扣联接、卡夹联接、压力装配联接的联接件材料选择、成型方法、联接原理、形状设计等。
- Research on interference fit riveting, composites structure riveting and driving interference-fit fastener have been done. 对电磁铆接技术在干涉配合铆接、复合材料结构铆接、干涉配合紧固件安装方面的应用进行了系统研究。
- But the interference fit by hydroform result in the damage occurring on the contact surface. 然而,由于锥套与辊颈利用液压胀形实现过盈装配,使得接触面间在装配过程中发生表面损伤。
- The interference fit between the gate and seats provides bubble tight shutoff, even under the lowest pressure. 即使在最低压力条件下，闸板和阀座之间的交互界面也能够实现气密性关闭。
- The interference fit between the gate and seat provides bubble tight shutoff even under the lowest pressure. 即使在最低的管线压力下，闸板与阀座之间的配合也能够实现气泡级密封功能。
- Bearings with a tapered bore are used when an interference fit is required for the inner rings on the roll neck, e. G. When rolling speeds are high. 在轧辊轴颈上的内圈需要过盈配合时,例如轧钢速度高时,使用带锥形孔的轴承。
- Interference fit is required between outer ring and housing as the load is varying in direction relative to the outer ring. 外圈与轴承座之间需要过盈配合,因为相对于外圈的负荷方向有变化。
- The process problems of composite structures using interference fit technology can be solved by use of Stress Wave Riveting (SWR). 分析了复合材料结构采用干涉配合技术存在的工艺困难，利用应力波铆接设备对碳纤维复合材料进行了干涉配合铆接试验，并对铆接质量进行了检测分析。
- The locknut torque needed to move the washer at the maximum washer interference fit shall not exceed the torques given in Table 3. 锁紧螺母扭矩压紧垫片时，其与垫片的最大相互作用力不能超过表3所给扭矩值。
- To dismount a bearing having an interference fit, the tools described in the following section may be used, the choice of tools will depend on bearing type, size and fit. 拆卸过盈配合的轴承,可使用下述各种工具,而工具的选择取决于轴承类型、大小和配合。
- Based on that,further analysis found regression curve is closely exponential function y=6.874e-4.604x in correlation between wood density and optimal value of interference fit. 在此基础上;进一步探讨最佳过盈配合量与木材密度的相关性;得到其回归拟合曲线近似为指数函数y=6.;874e-4
