您要查找的是不是：
- line speed rate 线速
- Great in drying ability, and it can increase projecting speed rate. 具有高超的干燥效力,增加射出速率。
- The actual delays depend on line speed and system load. 真正的延迟时间依赖于线路的速度和当时的系统负载。
- ASB is the damage reason in the condition of deformation at high speed rate. 可以说，绝热剪切带是材料高速率变形条件下损伤的原因。
- Its line speed of the rotor can reach to 52m/s to increase wallop to materials. 6.;特殊的安全销及调整机构(专利技术)，当发生异常冲击时有效保护机体。
- An inertia system can be used to make the capstan line speed stabilized. 3.;特殊的大惯量系统设计使系统的静态性能更好（选用），从而保证牵引速度的稳定。
- Changing the line speed may require you to change settings for ports on this line. Continue? 改变线路速度可能需要您更改这个线路上端口的设置。要继续吗?
- And discuss influence of hydraulic press loading in change speed rate pattern and superplasticity forging on parameters. 讨论了变应变速率模式液压机载荷和超塑性锻造影响参数的关系。
- When the software controls the whole system, the hardware transmits the users’ L2TP data packets in line speed. 在软件完成控制功能 的同时，对用户的数据报文利用硬件进行线速的转发。
- Acording to the speed rate of the first group.it has few of symptoms of ear upset or earache,so it is a more suitable pressure speed. 证实了按甲组速率方法加压，发生耳痛等不适证状者极少。因此是比较合适的加压速度。
- Located on the rolls of paper agencies and pull open-book inter-interagency hobber determines the line speed. 位于卷纸机构和不闭卷机构间的不推动滚不决了线速率。
- The optimum ball milling parameters were determined: ball gradation is 1:2:4,rotational speed rate is 170rpm, ratio of ball to powder is 20:1 and milling time is 15h. 经过正交试验确定的较优的球磨工艺参数为:磨球级配1:2:4,球磨机转速170rpm,球磨时间15h,球料比20:1。
- Abstract: This paper focuses on the synchronization of line speed among multi-axes of line cutter, provides the solution and control principle diagram. 摘要:本文针对线切割机多轴之间的线速度同步控制,提供一套解决的方法,并给出控制原理图。
- Under the condition of noisiness, whether the loaded speed rate can be measured will directly affect the control process and the quality of the testing. 当存在噪声时,加荷速率能否准确测量将直接影响控制过程与试验质量。
- Abstract：This paper focuses on the synchronization of line speed among multi-axes of line cutter, provides the solution and control principle diagram. 摘要：本文针对线切割机多轴之间的线速度同步控制，提供一套解决的方法，并给出控制原理图。
- In this study we investigate the effects of blade line speed and feeding speed on the cutting force, examine the photomicrograph of the cut off face. 理论部份，本研究以正交切削模式为基础，配合弓锯锯削模式，以建立切削参数与切削率间之关系。
- At right is the push Board crank (slider) guide rod mechanism, based on analytical method to extrapolate push Board line speed for the formula. 不左图是拉纸板的曲柄(不涩块)导杆机构简图，用分析法可拉演不入拉纸板的线速率公式。
- The system can monitor four major indexes in the spraying process, the spraying pressure, spraying flow, sprayer travel speed rate and the percentage of the remaining mix pesticide in the tank. 该系统可实时监测喷施农药过程中的喷雾压力、喷雾流量、喷雾机行走速度和药桶药液余量4个主要参数。
- Ultimate transmitting speeding rate of one demodulator is 38.4KBPS, which can completely meet the requirement of VOD feed-back. 单路传输速率最大为38.;4KBPS，能够充分满足视频点播回传的需求。
- Dealing with the numerator percentage goes mith the changing of temperature by using? Maxwell? scattered rule of Speed rate, we often meet the maths problems mith the comples nature of the scattered function. 利用麦克斯韦速率分布律讨论分子百分率随温度变化时,常因分布函数的复杂性而遇到数学困难。
