您要查找的是不是：
- Difference of pressure makes a liquid flow through a siphon. 压力差使得液体通过虹吸管。
- Wenzhou Yongchen Tube For Liquid Flow Co., Ltd. 温州永晨流体管道有限公司。
- LIQUID FLOW MEASUREMENT IN OPEN CHANNELS. PARSHALL AND SANIIRI FLUMES. 明渠液流测量。
- As of the flow of a liquid flowing,such as blood from a wound. 关于能流动的液体的流动，关于从伤口流出的鲜血。
- A liquid flows freely and has no fixed shape. 液体能自由流动,无固定形态。
- There is liquid flowing on the surface of Titan. 土卫六的表面有液体流动。
- Therefore, the general Reynolds equation is derived based on continually of liquid flow. 由此根据液流连续性推导出广义雷诺方程。
- Main factors affecting on liquid holdup are pressures, pipeline diameters and gas &liquid flow rate. 影响持液率的因素主要有压力、管径、气液相流量等。
- It was shown that the reasonably modified DJ trays and Linde sieve trays have a more uniform liquid flow. 认为由于DJ塔板与导向筛板采用了合理的改进措施，使得液流分布更均匀。
- When the liquid flow rate is high, the addition of gas into the flow would have less influence on the variation of WSS. 在高液流速度下，加入气泡后壁面切应力波动幅度的变化较小。
- The severe slugging can occur only when both gas and liquid flow rates are relatively low. 严重段塞流的发生严格受到气、液相流量大小的限制,只有在气、液两相流量都较小的工况下,严重段塞流才会发生;
- MEASUREMENT OF LIQUID FLOW IN OPEN CHANNELS. TRACER DILUTION METHODS FOR THE MEASUREMENT OF STEADY FLOW. PART 4: FLUORESCENT TRACERS. 明渠流量的测量。测量稳定流速用的示踪稀释法。第4部分:荧光示踪剂。
- The experimental data showed that the total pressure drop of the cross-flow RPB was influenced by rotating speed, gas flow rate and liquid flow rate. 实验表明错流旋转填料床的气相总压降与气体流量、旋转床转速、液体流量有关。
- It was found that gas injection at riser base could eliminate the severe slugging and stabilize the gas and liquid flow rates at the riser outlet. 实验结果表明,采用上升管下部注气的方法可以消除严重段塞流现象,实现管道出口气液的稳定流动,减小系统的最高压力,同时可以防止上游水平管内出现高频率的长液塞流动。
- It was summarized in present paper that the liquid flow acted in the transfers process, solidification structure and componential segregation. 文章从传输过程、凝固组织和成分偏析等三个方面对液相流动的作用作了综述。
- The principles and methods of the design of gas and liquid flow deflectors and atomizer/spray nozzles have been demonstrated in the fluidized bed. 阐明了流化床聚合反应器中气液导流器和喷雾器的设计原理和方法，详细分析了操作工艺条件与产品质量和产率之间的关系。
- JHYG piston Type liquid prover is a newly developed standard tool for measurement of liquid flow andquantity-value transmission. JHYG型活塞式液体标准体积管是新近研制成功的液体流量计量量值传递的标准器具。
- Based on coupling control of mechanical motion and liquid flow, an automatable adjusting technology for cell position and attitude was proposed. 基于机械运动和流场流动的耦合控制，提出了自动化的细胞位姿调节技术。
- The characteristics of K + desorption kinetics on noncalcareous fluvo-aquic soil under long-term fertilization condition were studied using the liquid flow technique. 采用连续液流法研究了长期定位施肥潮土K + 解吸的动力学特性。
- With bottom gas blowing at the tundish, the average residence time of steel liquid flow in the tundish can be prolonged effectively;the dead volume fraction can be reduced. 采用中间包底部吹气技术，当控制的吹气参数合理时，可以有效地延长钢液的平均停留时间，降低死区体积；
