您要查找的是不是：
- Main factors affecting on liquid holdup are pressures, pipeline diameters and gas &liquid flow rate. 影响持液率的因素主要有压力、管径、气液相流量等。
- When the liquid flow rate is high, the addition of gas into the flow would have less influence on the variation of WSS. 在高液流速度下，加入气泡后壁面切应力波动幅度的变化较小。
- The experimental data showed that the total pressure drop of the cross-flow RPB was influenced by rotating speed, gas flow rate and liquid flow rate. 实验表明错流旋转填料床的气相总压降与气体流量、旋转床转速、液体流量有关。
- The same amount of increase of liquid flow rate would result in approximately the same amount of increase of the WSS at the middle and bottom wall of the tube. 随着气相流速的增加，管道上部的壁面切应力有较小幅度的降低,管道中下部的壁面切应力有较大幅度的增加；
- Air and liquid backwashing, with airflow rate of 60m/h and liquid flow rate of 30m/h, is daily undertaken in this BAF system, which consumes 10% influent a day. BAF反冲洗采用气水联合反冲，每天1次，气反冲速度为60m/h，水反冲速度为30m/h，反冲洗约消耗日处理水量的10%25。
- Accurately deriving the true liquid flow velocity is the key for determining the stratification flow rate of oil and water and logging interpretation of liquid producing profile. 摘要准确求取流体的真实流动速度是确定油水各相分层流量及产液剖面测井解释的关键。
- The relations of volumetric mass transfer coefficient with rotating speed, liquid flow rate and gas flow rate were measured, and mass transfer characteristics of two packings were investigated. 对这两种不同形状的填料表面传质特性进行比较,找出传质效果较好的填料。
- The severe slugging can occur only when both gas and liquid flow rates are relatively low. 严重段塞流的发生严格受到气、液相流量大小的限制,只有在气、液两相流量都较小的工况下,严重段塞流才会发生;
- It was found that gas injection at riser base could eliminate the severe slugging and stabilize the gas and liquid flow rates at the riser outlet. 实验结果表明,采用上升管下部注气的方法可以消除严重段塞流现象,实现管道出口气液的稳定流动,减小系统的最高压力,同时可以防止上游水平管内出现高频率的长液塞流动。
- gas well with liquid flow rate being zero 气井零液流量
- liquid flow rates per unit weir length, 20, 30, 45 and 60m3/m. h; 液流强度为20、30、45、60m~3/m·h;
- Consistent flow rate from nebulizer to nebulizer. 在雾化器间提供持续稳定的流通速率。
- Difference of pressure makes a liquid flow through a siphon. 压力差使得液体通过虹吸管。
- Wenzhou Yongchen Tube For Liquid Flow Co., Ltd. 温州永晨流体管道有限公司。
- Affect the melt flow rate and the cooling speed. 会影响熔体的流动性和冷却速度。
- Possibility to control the flow rate by Pump. 由蠕动泵调节盐溶流量。
- Typical maximum system flow rate (7.5 feet/sec. 标准最大系统流量为7.;5英尺/秒。
- The HTA flow rate has two-faced influences on them. 热风流量对其影响呈现两面性。
- A Hydrodynamic Model for Gas-lifting Flow in a Gas Well with Liquid Flow Rate Being Zero 天然气井零液流量气提流动的水动力学模型
- Effects of Liquid Flow Rate and Surface-to-nozzle Distance on Non-boiling Heat Transfer Performance in Spray Cooling 无沸腾喷雾冷却中流量和喷头高度对换热性能的影响
