您要查找的是不是:
- Too low melt temperature: Inhomogeneous melt with cold material inside (Which cause empty parts, broken parts etc. 熔体温度太低:材料塑化不均,熔体内含冷料(从而造成充模不足,冷料,产品断裂等)
- In addition, jewelry alloys used in wax setting and casting must have the properties of low melting temperature, good fluidity and anti oxidization properties. 用于蜡镶铸造的合金应具有较低的熔点、较好的流动性及抗氧化性能等。
- The four-components copolyesters in certain range of compositions have low melting temperature, steady mesophase in a broad temperature range and fiber-forming tendency. 一定组成范围的四元共聚酯具有低熔点,宽液晶相区,易成纤的特点。
- Differential scanning calorimetry (DSC) results show that the corn starch plasticized with glycerol has a lower melting temperature than pure corn starch. 差示扫描量热分析(DSC)研究发现。甘油塑化淀粉的熔融温度比普通淀粉的低。
- Linear aliphatic polyesters with the lower melting temperature was more susceptible to biodegradation than the linear aliphatic polyesters with the higher melting temperature. 线性脂肪聚酯中的降解性同熔点和亲水性都有关系。
- The results show that PHB/PET/VA ter-polyester with vanillic acid has faster copolycondensation rate, lower melting temperature, typical thermotropic liquid crystallinity and better spinnability. 发现含香草酸第三单体的PHB/PET/VA三元共聚酯具有较快共聚反应速率、较低熔融温度、典型热致液晶行为和良好成纤性。
- Composition Study of Machinable Glass Ceramics with Low Melting Temperature 低熔化温度可切削玻璃陶瓷的成分研究
- Microstructure and Properties of a Machinable Glass Ceramic with Low Melting Temperature 低熔点可切削微晶玻璃的组织与性能
- How is melt temperature controlled? 如何控制熔炼温度?
- low melting temperature agarose 低熔点琼脂糖
- Aluminum-silicon alloy casting their low melting point, formability, and can also be used for the production of foam material. 铝-硅系铸造合金因其熔点低,成形性好,也可用于制作泡沫材料。
- Account should be taken of the low melting point of this substance. 应该考虑到这种物质的熔点低.
- Its melt temperature is high and it has proper viscosity and low temperature flexibility. 具有较高的熔融温度,适宜的粘度和良好的低温柔韧性;
- Keywords metallic nanoparticle;size and shape effect;cohesive ener gy;melting temperature;minimum cri tical size;lowest melting temperat ure; 关键词金属纳米微粒;尺寸形状效应;结合能;熔点;最小临界尺寸;最低熔化温度;
- The Zn-Al alloy has many advantages, such as good mechanical property, strong antifriction property, processable property, small density, low melting point, affluent raw material, low cost and so on. 高铝锌基合金具有优良的力学性能、耐摩性能、机加工性能、以及密度小、熔点低、原材料来源丰富和成本低等优点。
- The influences of lithia content on the melting temperature,mechanical properties and thermal expansion coefficient of low temperature frit were studied. 本文研究了氧化锂加入量对低温熔块的熔融温度、力学性能、热膨胀系数的影响。
- Polypropylene(PP) had poor foamability because of its low melt strength. 聚丙烯(PP)熔体强度低,发泡性能差。
- The rheology properties of polymer filled with lower melting point dual component metallic alloy were studied by Hakke rheometer. 利用哈克流变仪对低熔点双组分合金填充聚合物材料体系的流变性进行了研究。
- The heat of fusion is the heat required to melt a substance at its normal melting temperature. 熔化热是一种物质在其熔点温度全部熔化所需要的热量。
- An advanced niobium-silicide based ultrahigh temperature alloy was prepared by vacuum consumable arc-melting method. 本文设计了新型Nb硅化物基超高温合金的成分,并采用真空自耗电弧熔炼法制备了其母合金锭。