您要查找的是不是:
- This is a very strong and thick fascia, which extends anterolaterally from the lumbar spine. There are three distinct layers of the lumbodorsal fascia. 腰背筋膜从后部中线开始,生长在腰脊椎上。
- The sacrospinalis muscle and three anterolateral flank muscle layers are seen in cut section, and the three layers of the lumbodorsal fascia posteriorly can be appreciated. 在切口断面可以看到荐棘肌和前外侧横腹肌层,从后部还可以看到腰背筋膜的三层组织。
- The lumbodorsal fascia and costovertebral ligament are visualized, arising from the transverse processes of the lumbar vertebrae.The relation of the kidney and pleura is also shown. 可以看到从腰脊柱的横突处长出的腰背筋膜和肋椎韧带,图上标明了胸膜和肾的关系。
- Posterior Musculature and Lumbodorsal Fascia 后部肌肉组织和腰背筋膜
- tendinous arch of lumbodorsal fascia 腰背筋膜腱弓
- Methods Epidural paracenletic needle was used to detach the lumbodorsal fasciae and block them under the localization and guidance of the"C" arm X-ray machine. 方法采用硬膜外穿刺针行第3腰椎横突周围筋膜松解和局部封闭治疗,术中用C型X线机准确定位;先行局部封闭,然后在局麻下行筋膜松解。
- lumbodorsal fascia 腰背筋膜, 胸腰筋膜
- Install fascia onto bumper assembly. 将仪表板安装在保险杆组合上。
- Including deep fascia of neck and musculas p... 包括颈阔肌、颈深筋膜的彻底松解是手术成功的关键。
- Minor thenar-hitting, lumbodorsal portion and limbs region. 小鱼际击法适用于腰背与四肢部。
- Disengage fascia from hooks on bottom of front fenders. 将仪表板从前挡泥板底部的挂钩上取下。
- The superficial branch lies outside the anterior prostatic fascia. 浅表支走在前列腺筋膜前层的外表面。
- The lower fascia splitter is punctuated by two fairings. 较低的筋膜分离器是由两个整流罩打断。
- Install plastic rivets to hold bottom of rear fascia to bumper reinforcement. 将固定后面板在保险杆加强组件的塑胶铆钉安装好。
- The breast tissue is dissected posteriorly to the pectoralis muscle and fascia. 将乳房组织向后剥离至胸肌和胸肌筋膜。
- Install bolts to hold fascia to headlamp mounting panel at each side of grille. 将固定面板在风栅两侧头灯固定板的螺栓安装好。
- The methods of tendon or fascia fixation and bone grafting are discussed here. 本章主要介绍肌腱和筋膜固定方法及骨移植。
- Install push-in fasteners holding fascia to quarter panel at wheelwell opening. 安装将面板紧固到车轮井开口的四分之一扇形盘上的推进式固定件。
- Install push-in fasteners holding trunk lid slam bumpers to top of fascia. 安装将行李厢盖沿保险杆紧固到面板顶部上的推进式固定件。
- Install push-in fastener holding center of fascia to rear closure panel. 安装中心面板紧固到后罩盘上的推进式固定件。