您要查找的是不是：
- The structure of the main shaft bearing assembly can decide its using conditions. 主轴轴承的结构形式又决定了螺杆钻具的使用条件。
- The paper presents the vibration timing effect process used on engine block of 16V280ZJ diesel engine. The correctness of the process is validated by measuring scanned curve and coaxiality of main shaft bore and camshaft bore. 介绍了 16 V2 80 ZJ型柴油机机体振动时效的工艺 ,通过扫频曲线和主轴孔、凸轮轴孔同轴度的测量验证了采用该工艺的正确性。
- starter main shaft bearing 起动机主轴轴承
- main shaft bearing 主轴轴承
- main shaft bearing cap 主轴轴承盖
- The hollow stemlike main shaft of a feather. 翎管羽毛的中空的茎状羽干
- main shaft bearing cover 主轴轴承盖
- The bottom bearing applies both labyrinth seal and frame seal, which have good performance of sealing. The main shaft is anticorrosive. 下轴承端盖密封采用双重密封，可确保密封效果，主轴采用防腐新技术，能保护主轴免受腐蚀。
- A secondary mine passageway between two main shafts or tunnels. 次要矿山甬道矿井中连接两条大隧道的小巷道
- Main shaft bow bearing pedestal uses water-cooling device for continuous operation without overheating and for longer sevice life of bearing . 主轴箱思承采用水冷装置，因此连续长时间使用不发热、不高温、延长轴承使用寿命。
- In order to prevent the reduction of the working accuracy of S1-280 Type Lathe that is made from overwear of main shaft bush bearing, it is substituted with rolling bearing. 原车床主轴支撑滑动轴承轴瓦严重磨损,加工精度降低,故改用滚动轴承支撑。
- It s a important join component of hydrogenerator main shaft fasten joint bolt. 水轮发电机主轴联轴螺栓是水轮发电机重要的联接部件。
- The main parts of pump are suction-stage, middle-stage, discharge-stage, bearing support, motor support, impeller, diffusor, shaft, shaft bearing, shaft sleeve, balance kettle, balance sleeve etc. 泵主要由进水段、中段、出水段、轴承支架、电机支架、叶轮、导叶、轴、轴承、轴套、平衡鼓、平衡套等零件构成。
- It theoretically and practically summarizes the gist of emergency repair of tunnel shaft bearing of ships. 从理论和实践两个方面概括了应急修理中间轴承的要点。
- Ascertain the first bolt of the M/E aft end and the position of the intermedial shaft bearing. 初定主机末端第一颗地脚螺孔位置，初定中间轴承位置。
- Main shaft bearings 主轴轴承
- This was why the tail shaft bearing, etc. worn more seriously and the white metal thereon melted and badly scored. 这就是尾轴轴承等更加严重磨损，其上面的白合金熔化和严重拉痕的原因。
- Shell Turbo T oils, available in ISO grades 32, 46, 68 and 100, are suitable as lubricating oils for main shaft bearings and mechanical gears for application in the following areas 壳牌多宝T涡轮机油采用ISO等级32、46、68和100，均可作为以下领域中使用的主轴承和机械齿轮的润滑油。
- Install axle shaft bearing with Installer 6436 and Handle C–417Ensure part number on the bearing is against the installer. 用安装工具6436和手柄C–4171安装车轴轴承。确保轴承上的零件号对着安装工具。
- Install axle shaft bearing with Installer 6436 and Handle C–417Ensure that the part number on the bearing is against the installer. 用安装工具6436和柄C–4171安装主动轴轴承。要保证轴承部件号码对着安装工具。
