您要查找的是不是：
- Estimation of duplicate routing for WSN based on minimum hop count routing 最小跳数路由无线传感器网络中的路由数估计
- minimum hop count routing 最小跳数路由
- hop count routing 跳数场路由
- The IP address in the Received: header field is used for hop count and routing loop detection. Received:头字段中的IP地址用于跃点计数和路由循环检测。
- The default maximum hop count is 15. 默认最大跃点计数为15。
- Destination is known as the hop count. 在不同的目的去决定跳数。
- Hop count is used as the metric for path selection. 跳跃数被用来当作路径选择的权值。
- Using the method of combining hop count and ETX can avoid routing cycle and build up the network topology quickly. 另外,将跳数与ETX尺度相结合,避免了路由循环,能够快速建立网络拓扑。
- RIP is a distance vector routing protocol that uses hop count as its metric to determine the direction and distance to any link in the internetwork. RIP是一个距离向量路由协定，它使用跳跃数当做权值来决定到互连网路上的任何链结的方向和距离；
- The distance-vector routing approach determines the distance and direction, vector, to any link in the internetwork.The distance may be the hop count to the link. 距离向量路由方法决定到互连网路上的任何链结的距离和方向，距离与方向即是向量，距离可以是到链结的跳跃数；
- Cause: The maximum hop count was exceeded for this message. 原因:此邮件超出了最大跃点计数。
- Increase the hop count on the appropriate SMTP virtual servers. 增加相应SMTP虚拟服务器上的跃点计数。
- When an Edge Transport server is protected by a router or firewall that uses Network Address Translation (NAT), NAT disrupts the Edge Transport server's hop count and routing loop calculations. 当边缘传输服务器受使用网络地址转换(NAT)的路由器或防火墙保护时,则NAT会中断边缘传输服务器的跃点计数和路由循环计算。
- Unable to deliver message because the maximum hop count was exceeded. 无法传递邮件,因为超出了最大跃点计数。
- The hop count to use depends on the organization's Exchange topology. 要使用的跃点计数取决于组织的Exchange拓扑。
- SSPP firstly computes a minimum hop primary path for each connection request, and it follows to compute two SRLG disjoint and minimum cost backup paths for each sub-path on the primary path. 共享子通路保护为每条业务请求计算一条最短的工作路由，并为工作路由上每段子通路各计算两条共享风险链路组分离且代价最小的保护路由。
- This maximum hop count greatly restricts the use of RIP in large internetworks but prevents counts to infinity and endless network routing loops. 最大跳跃数大大地限制了RIP于大型互连网路之使用，但避免了无限计数和无穷的网路路由迴圈。
- Whether the actual path includes a circular routing path or too many hops, the packet will eventually exceed the maximum hop count. 假如实际的路径包括循环的绕送路径或太多的跳跃，封包最后将超过最大跳跃数。
- In the Advanced Delivery dialog box, type a new value in the Maximum hop count box. 在“高级传递”对话框中,在“最大跃点计数”框中键入新的值。
- The default maximum hop count for SMTP virtual servers in Exchange Server 2003 is 30. 在Exchange Server 2003中,SMTP虚拟服务器的最大默认跃点计数是30。
