您要查找的是不是：
- CAUTION: The check valve spring is in compression. 警告：止回阀弹簧处于压缩状态。
- modulus in compression 压缩模数
- Does a neutron star represent the ultimate in compression? 中子星是压缩的最终产物吗?
- Cracks may initiate in compression, and certainly in tension. 裂缝可能在压缩载荷下形成，当然也可能在拉伸载荷下形成。
- For most materials the modulus of elasticity in compression is the same as in tension. 对于大多数材料来说，受压缩与受拉伸的弹性模量是相同的。
- Do not install EPDM liner in compressed air lines. 在压缩空气管道中不要安装EPDM衬垫的阀门。
- elastic modulus in tension and compression 拉压模量
- You run this file in extracting all of them in compressed form. 你办这个档案中提取它们全部压缩形式。
- The calculation method of drainage modulus in agricultural diked area is inapplicable in urban diked area. 摘要农业圩区原有的排涝模数计算方法已不适用于城镇圩区。
- The shortcomings in substituting deformation modulus by unloading modulus in the damage calculation are analyzed. 分析了以往用卸载刚度代替变形模量所带来的问题.
- Also, a dynamic measurement method of Young's modulus in principal axis direction for alaminae with orth-woven fibers was presented. 为说明动态法的有效性，作者还进行了铝合金板材弹性模量和泊松比的动态和静态测试。
- In addition, PCE reduced the ovariectomy-induced decrease in bending stiffness, bending energy and Young's modulus in femoral bone . 此外，PCE可以明显地减缓因去卵巢后而降低的骨应力数值，包括有提升骨骼硬度、骨骼最大负荷能量值与杨氏系数。
- Since the glass is in compression, it cannot extend appreciably beyond the ends of the eyelet. 因为玻璃处于压缩状态，玻璃不能明显地延伸到超过座孔的端面。
- Environment protection monitor processing system. System installation guide is in compression documents. 环保数据监测处理系统,系统的安装说明在压缩文件中
- The experimental results showed that the elastic modulus in tension and bending reaches the optinal value when the ratio between braided yarns and axial yarns is 50/50 and 75/25. 在交织纱和轴纱的比例分别为50/50和75/25时，材料的拉伸弹性模量和弯曲弹性模量达到最佳值。
- Solid bodies in this book: bars with axial loads, shafts in torsion, beams in bending, and columns in compression. 本书中的固体主要包含：受轴向力的杆；受扭矩的轴；受弯矩的梁和受压的（柱？桁架？）。
- Results show that the shape and relative thickness of section,section modulus in bending are the main factors that determine the bending properties of the profiles. 结果表明,型材的截面形状、相对厚度及抗弯截面系数等是决定弯曲性能的主要因素。
- Flat braided-aluminum straps are held in compression with stainless steel clamps to this metallized area. 用不锈钢卡具将这层铝带固定在金属化的区域。
- If we replace the Young's modulus in the theoretical buckle formula by the Young's modulus mentioned above, the theoretical formula fits the simulation results well. 而以介质在振幅加强方向，与硬层在岩层缩短方向上的这两个弹性模数代入褶皱理论公式之中所得到的等效式，和数值模拟结果相当符合。
- Testing concrete in structures - Part 1: cored specimens - Taking, examining and testing in compression. 结构中的试验混凝土.;第1部分:芯样本
