您要查找的是不是：
- oil pump feed 油泵供油
- Taian Wuzhou Oil Pump And Oil Nozzle Co., Ltd. 泰安五洲油泵油嘴有限公司。
- Excavation for fuel oil pump house is in progress. 燃油泵房开挖工作正在进行。
- Feed spot: Single pump feed dian2-12, if with piece type oil feeder coordination use, then may satisfy utility-type unit more lubrication points the uses. 供油点多：单泵供油点2-12个，若与片式给油器配合使用，则可满足大型机组更多润滑点的使用。
- Activates the auxiliary oil pump. 辅助油泵激活按钮。
- With pump feed and continuous mill, it also applies to small lot manufacture. 泵浦输送，连续式研磨，所以也可以进行小批量生产。
- The feed pump must be auto-controlled to keep the pressure in feed line of the unit, so did the assistant lubricating oil pump. 为保证装置进料压力稳定,进料泵必须具备自动启动功能,进料泵辅助油泵也必须同时具备自动启动功能。
- The feed pump must be auto-controlled to keep the pressure in feed line of the unit, so did the assist lubricating oil pump. 为保证装置进料压力稳定,进料泵必须具备自动启动功能,进料泵辅助油泵也必须同时具备自动启动功能。
- In the combination splash and pressure feed lubricating system, an oil pump takes oil from the oil pan and forces it through holes drilled in the engine block and crankshaft. 在飞溅与压力结合式送油润滑系统中;油泵从油盘中把油抽上来并压入发动机机体上和曲轴上的油道中.
- Stop the running of one oil pump of the electric motor. 停止电机一油泵的运转。
- We are looking for supplier of oil pump PARTS brand name CTR. 我们需要求购汽车机油泵，请联系我们。
- The pressure of lube oil pump increases very slowly. 机油泵压力增长很慢。
- Automatic oil pump and fault alarm syster, dygnosis and instructions. 自动注油,自动故障报警、诊断,指导处理。
- BEIJING CITY GUOXING AUTOMOBILE OIL PUMP FACTORY MANUFACTURING CO., LTD. 北京市国兴汽车油泵制造有限公司。
- Exhibits: Forging, brake disc, DrivingShaft, engine, oil pump, Steering Gear. 展品锻件、制动系统、传动轴、水泵、机油泵、转向器。
- Main products: oil tank, oil tube, oiler support, oil pump, oil applying wheel etc. 产品主要结构：油箱、油管、安装支架、油泵总成及涂油轮等组成。
- Users refused to pay the lower lift costs, high pressure pumps fees. 低层用户拒交电梯费、高压水泵费等。
- This paper proposes a design project of the dynamoelectric accelerograph control system of X-aeroengine oil pump modulator. 提出了一种某航空发动机油泵调节器电动油门控制系统的设计方案。
- The rubber formulation of oil pump bushing was designed by orthogonal testing method design for on NBR(N - 41 ). 选用丁腈橡胶（N-41）为基础胶，利用正交试验法设计出抽油泵衬套橡胶配方。
- The oil pump should be close to the oil tank as possible as it can, the suction height should be no more than 500mm. 油泵应尽量接近油箱,吸入高度不得大于500毫米。
