您要查找的是不是：
- Effect of the Unit Length Energy on the Hardening Depth by Plasma Arc Surface Quenching 等离子弧表面淬火的单位长度能量对硬化深度的影响
- A Research on Surface Quenching for Fluted Roll of Roller Mill by Plasma Arc 磨粉机齿辊等离子弧表面淬火硬化技术研究
- In recent years, high power density beam powder surfacing techniques have been developing rapidly,such as plasma arc surfacing,electron beam surfacing,laser surfacing and focusing light surfacing. 近年来,高能束粉末堆焊技术凭借其特有的优势得到了迅速的发展。
- Structure and Hardness of Nickel-based Alloy Plasma Arc Surfacing 镍基合金等离子弧堆焊组织结构和显微硬度
- There are two reprocessed technologies after plasma arc quenching,they are lapped finishing and chemical running-in. 等离子弧淬火后处理工艺主要采用研磨和化学跑合2种方法。
- Composition Optimization of Composite Powder for Plasma Arc Surfacing 等离子弧堆焊复合粉末成分优化设计
- MICROSTRUCTURE OF THE COBALT- BASE ALLOY POWDER PLASMA ARC SURFACING 钴基合金粉末等离子弧堆焊的显微结构
- Study on Properties of Nickel-based Alloy Powder by Plasma Arc Surfacing 镍基合金粉末等离子弧堆焊层的性能研究
- Plasma Arc Surface Hardening 等离子弧表面硬化
- The hardness of 45 steel by surface quenching with plasma was about HV800,the method of heat treatment by using plasma as heat source was feasible. 45号钢经等离子体表面淬火后,淬火硬度在HV800左右,采用等离子体热源对工件进行热处理是可行的。
- The hardness of 45 steel through surface quenching with plasma reaches about 800 HV.Thus, the method of heat treatment using plasma as heat source is practical. 45号钢经等离子体表面淬火后,硬度在800HV左右,表明采用等离子体热源对工件进行热处理是可行的。
- Magnetic field control on microstructure and properties of plasma arc surfacing layer 等离子弧堆焊层的组织与性能的磁场控制
- Microstructure and wear resrstance of copper base alloy surfacing weld of plasma arc surfacing 等离子弧喷焊铜基合金的组织和耐磨性
- Plasma arc thermal spray welding is a kind of surface harden engineering by taking plasma arc as themal resource and certain alloy power as additive. 等离子弧热喷焊技术是一种以等离子弧为热源,以一定成分的合金粉末作为填充金属的表面强化技术。
- Surface quenching hardness for different steel types are specified according to modules along with the depth of carbonized layer and the hardness match between meshed gears. 按模数大小规定了不同钢种的表面淬火硬度以及关于渗碳层深度和相啮合齿轮的硬度匹配。
- Abstract: The working principle, structure and parameters design of plasma arc generator for heat treatment are described. Experiment has shown that it has good effect on partial surface hardening. 文摘:论述了用于金属材料表面热处理的等离子弧发生器的工作原理、结构特点和参数设计。试验证明这种发生器对材料的表面局部硬化非常有效。
- The hardness of camshaft surface quenching layer by laser surface heat treatment has been greatly improved.This is benefit to increase the surface fatigue strength of camshaft. 激光表面热处理后的凸轮轴表面淬硬层硬度有大幅度的增加，有利于提高凸轮轴表面抗疲劳强度。
- Hot wire plasma arc surfacing 热丝等离子弧堆焊
- plasma arc surfacing welding 等离子堆焊
- plasma arc surfacing 等离子弧堆焊,等离子弧埋焊
