您要查找的是不是:
- Pre-heat suggested when MIG overlay welding for large size products and use pulsed arc welding while overlay the steel. 特别适合镀锌皮的MIG焊接,用于大焊件的MIG堆焊时建议预热,堆焊钢材时建议使用脉冲电弧焊。
- TAW-P argon tungsten pulsed arc welding 钨极脉冲氩弧焊
- An AC Arc Welding Power Source with Pulsed Arc Stabilizer 脉冲稳弧的交流弧焊机
- Study on Principle and Technical Characteristics of High Frequency Pulsed Arc Welding Inverter 高频脉冲弧焊逆变器原理与工艺性能的研究
- This article analyzes and investigates the principle of the electric circuit and the welding characteristics of an AC arc welding power source with pulsed arc stabilizer 本文就采用脉冲稳弧的交流弧焊机的电路原理、焊接性能进行了分析和探讨。
- The development of thyristor puls plasma arc welding power source is introduced in this paper. 本文介绍了晶闸管脉冲等离子弧焊电源的研制成果。
- pulsed arc welding 脉冲弧焊
- pulsed arc welding rectifier 脉冲弧焊整流器
- For Automatic Welding-Electric Arc welding goggles and ccd imaging system. 用于自动变光电焊焊接护目镜以及看焊缝的ccd成像系统。
- Corrosion resistance and high strength. Argon arc welding of aluminum alloys. 耐蚀,强度高。铝合金氩弧焊用。
- Wear resistance. Argon arc welding of copper alloys and surfacing of steel. 耐磨性好。铜合金氩弧焊及钢的堆焊用。
- A CAD system of AC arc welding transformers called AWVTCAD was studied. 本文对交流弧焊变压器的计算机辅助设计系统进行了研究,简称“AWVTCAD”,结果表明利用该系统对弧焊变压器设计,不仅能提高计算精度与速度,而且也减轻了设计者的劳动强度及降低设计成本。
- It is perfectphase trigger circuit for arc welding power source of scr. 该相控触发电路是晶闸管整流弧焊电源的理想触发电路。
- Furthermore, it controls the dynamic current rise behavior, the maximum current, and the droplet transition during the pulsed arc process. 此外,它在脉冲处理过程中能够控制动态电流提升性能,最大电流和熔滴过渡。
- Perhaps I need to pull apart another SCR and try the arc welding approach. 也许我需要把除了另一可控硅和审判电弧焊接的办法。
- Use manual metalic arc welding, the type of electrod is A102 for material 304. 设备采用手工电弧焊,304材质焊条牌号为A102。
- Arc brazing has the characteristics of braze welding and arc welding. 电弧钎焊是近十年来才发展起来的一种新型硬钎焊工艺,兼有钎焊和电弧焊的特点。
- Such as electric arc welding, carbon dioxide gas shielded arc welding, TIG etc. 如:电弧焊、二氧化碳气体保护焊、氩弧焊等各种焊接。
- Pulse Arc Mode is perfect for ring resizing, porosity, seams, adding material, welding thicker materials and any general manufacturing and repairs. 脉冲电弧模式是环大小,孔隙度,接缝,增加材料,焊接较厚的材料和任何一般制造和修理的完美选择。
- The effect of discharge conditions on degradation of P-nitrophenol in organicpollution water with pulsed arc discharge plasma at atmospheric pressure was investigated in this paper. 摘要利用大气压下脉冲电弧等离子体对含对硝基苯酚的有机废水进行处理,研究放电条件对废水处理效果的影响。