您要查找的是不是：
- General Installation Information: Sump Pump Swing Check Valves may be installed in either vertical up-flow (see illustration) or horizontal positions on pump discharge line. 一般安装信息：水坑泵旋启式止回阀既可安装在垂直朝上（参阅图示）的泵排放管道上，也可安装在水平的泵排放管道上。
- hydraulic oil pump discharge line 液压油泵泄放管路
- hvdraulic oil pump discharge line 液压油泵泄放管路
- Must be connected to an adequate discharge line. 必须与适当的排泄管道连接。
- Make sure pump discharge TRV in correct position. 确认泵出口管线TRV流程已通。
- pump discharge line 泵排出管
- Compare and analysis of theoretical study and experimental measurement of pressure pulse of reciprocating pump discharge lines 往复泵排出管线压力脉动理论研究与实验对比分析
- CTC maximum head is suitable for pump discharge to Butanol handling facility. 用户确认泵出口去丁醇处理装置的最大扬程是合适的.
- Vertical discharge line must be installed with its direction downward. 必须安装垂直排泄管,其方向朝下。
- Never pipe the discharge line directly into a drainage ditch, sewer or sump. 不要把排泄管直接插入排泄地漏、污水管或污水坑里。
- Must be installed to allow complete drainage of both the valve and discharge line. 必须安装到具有完全排泄能力的阀门和排泄管上。
- Indicating pressure transmitters shall be used in preference over pressure gauges except for pump discharge. 带指示的压力变送器除了泵出口应优先于现场压力表被使用。
- Must be installed to allow complete drainage of both the temperature and pressure relief valve and the discharge line. 必须正确安装,使得降温减压安全阀和排水管道都能够完全排泄。
- Must not be capped, blocked, plugged, or contain any valve between the relief valve and the end of the discharge line. 在安全阀和排泄管之间不要加盖、闭塞、堵塞或包含任何阀门。
- NOTE: On pump discharge, the preferred check valves are an in-line spring loaded, swing design with lever and weight or lever and spring. 注意:在泵的排泄口处,首选的止回阀是管内弹簧负载,旋启式,配置杠杆和重量或杠杆和弹簧。
- Use short or standard length thermostat. Vertical discharge line must be installed with its direction downward. 适用于较短或标准长度温控杆。垂直排泄管必须安装在它的下方。
- On pump discharge, the preferred check valves are in-line spring loaded, swing design with lever and weight or lever and spring. 在泵出口处,首选止回阀是管内弹簧负载,配置杠杆和重量旋启式结构,或杠杆和弹簧旋启式结构。
- This pipe is connected to the suction line and that one over there to the discharge line. 这根管子与上水管连通,那根管子与排水管连通。
- Note: Preferred mounting of check valves of any manufacturer is 5 pipe diameters downstream from the pump discharge or pipe elbow. 注释：任何制造商的止回阀最好安装在泵排泄口或管道弯头下游5倍管道直径的位置。
- The end of the discharge line opening should terminate near a floor drain or other suitable location not subject to blocking or freezing. 排泄管道的终端开口必须靠近地漏或其他不会堵塞或冻结的地方。
